Kenwood LSF-1010 - Manuals

LSF-1010 (EN) 6 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Location and Orientation Attaching the Cushions Attach four cushions to the base of the subwoofer, one at each corner, as shown below.The cushions prevent the subwoofer from sliding, and dampen its vibrations. (Cushionsare included in the ...

7 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Location and Orientation Location Precautions Interference with AM Reception The subwoofer utilizes digital circuitry to provide efficient signal amplification. Placingthe subwoofer too close to your AM receiver (AM tuner) may therefore ca...

LSF-1010 (EN) 8 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Setting Up the Satellite Speakers For standard setup, mount each speakerto a stand as described below. A s a n a l t e r n a t i v e t o t h e s t a n d a r dsetup, it is also possible to mount thespeakers onto a wall or to set them upwith...

9 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO 2. Attach the arm to the stand. Push the clip open (see illustration) andfit onto the pole. 3. Plug the speaker cord into the base of the stand. Plug the cord extending from the speakerinto the jack on the base of the stand. Clip Base Pole...

LSF-1010 (EN) 10 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Before Connecting... Making Connections Note Note 1. Be sure to connect all cables securely. Insecure connections may result in distortion or noise.2. Always unplug the power cord before connecting or disconnecting cables. Leaving the pow...

11 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO White stripe Connecting to Amp's SUBWOOFER PRE-OUT Jack Using the pin-plug audio cable that came with the subwoofer, connectthe SUBWOOFER PRE-OUT jack on your amplifier or receiver to the L/(MONO) LINE IN jack on the subwoofer. CAUTION Do...

LSF-1010 (EN) 12 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Connecting to Amp's Speaker Output Terminals Connect the FROM AMPLIFIER terminals on the subwoofer to thespeaker output terminals on your amplifier or receiver. Connect theTO SPEAKERS terminals on the subwoofer to your front speakers. Mak...

13 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Connecting to Amp's Standard PRE-OUT Jacks Connect the PRE-OUT jacks on the amp or receiver to the LINE IN jackson the subwoofer. Make the connection using pin-plug audio cable.(The cable is not included with the subwoofer.) CAUTION Do no...

LSF-1010 (EN) 14 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS 1 POWER switch Press this switch to set the subwoofer's power on or off. 2 POWER indicator Indicator lights up when power is on. 3 VOLUME adjuster dial 4 PHASE switch 5 TURNOVER FREQUENCY adjuster dial Components and Their Functions Adjus...

15 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Important Operating Notes Satellite Speakers 1. The satellite speakers have a nominal impedance of 6 ohms. To ensure safe and efficient speaker operation, be sure that your amplifier or receiver is ableto work with 6-ohm speakers. 2. The ...

LSF-1010 (EN) 16 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS You can adjust the position of the speaker by changing the height and angle ofthe arm. Getting Ready to Adjust Loosen the two arm screws holding the arm in place (one screw on each side ofthe arm), so that you can move the arm up and down...

17 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Adjusting the Satellite Speaker Position Adjusting the Arm Angle You can set the arm to any of five different angles by adjusting the angle of thearm holders. 1. Remove the arm. 1 Loosen the two arm screws (one screwon each side of the ar...

LSF-1010 (EN) 18 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS As an alternative to the standard setup, you can also mount the satellite speakersin any of the following configurations. • Sideways on the stand (“Offset mount”)• On the wall (“Wall mount”)• Without the stand (“Clip-on mount”) Offset Mou...

19 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Other Ways to Set Up the Satellite Speakers Wall Mount You can mount the satellite speaker stands on the wall as described below. Precautions Please observe the following precautions when mounting speaker stands ontothe wall.• Be sure tha...

21 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Clip-on Mount Use the following procedure to clip the speaker onto an object other than thebase. You can clip to either a cylindrical fixture (such as a thin pipe) or a flat-edgefixture (such as the edge of a bookshelf). Conditions If fla...

LSF-1010 (EN) 22 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS 3. Attach and fasten the arm. 1 Fit the arm through the holes in the armholders, adjust it to the desire height,and then tighten the arm screws. 2 Place the screw caps back over the armscrews. You may now want to readjust the angle of the...

23 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Cleaning You can clean the panel for subwoofer and satellite speaker and casing by wip-ing with a soft cloth. Never clean with alcohol, benzene, paint thinner, or othersuch solvents, as these may cause discoloration. Contact Restorers Nev...

LSF-1010 (EN) 24 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS If the subwoofer does not seem to be working correctly, the following advice may help you correct the problem. Troubleshooting Volume is too low. * Speaker cords are reversed. * The phase setting is not appropriate.* The amp or receiver's...

25 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Specifications Subwoofer System ........................... Subwoofer system with built-in amplifier (Magnetically shielded) [Audio section]Rated Output Power ..................................... 40 W DIN (300 Hz, 6 Ω ) Output Power .......

For your records Record the serial number, found on the back of the subwoofer, in thespaces designated on the warranty card, and in the space provided atright. Refer to the model and serial numbers whenever you call uponyour dealer for information or service on this product. Model .....................