JVC K3-R - Manuals

JVC K3-R – Manual in PDF format online.

Manuals:

Manual

Manual JVC K3-R

Summary

Page 2 - Installation & Operation; Manual Switch Control; AB Switch Status Indication; ON; Indicates the power supply source is connected.

K3 System Page 2 Installation & Operation K3 Chassis The K3 Chassis holds the Power, Control and A/B Switch modules for the K3 system. It installs in a standard 19” EIA equipment cabinet, requiring 1.75” (1U) of rack height. K3 systems are preconfigured and tested in the factory. All Control, Po...

Page 3 - Power Supplies Modules; Internal -48VDC Power Supply

K3 System Page 3 Power Supply 1930077 Converts 110/ 220 /240 VAC to 24VDC Single Slot Redundant Capable Input Power Nominal : 120/240 VAC 50/60 Hz Range : 100 - 240 VAC Watts: 50 Fusing: 2 A Environmental Operating: 0 C - +65C Physical AC Input connector: IEC 320 (C14) on rear panel Alarm / Expansio...

Page 4 - Alarm Connector; Pin 6 NO; Input Power

K3 1RU AB Switch Page 4 Alarm Connector Alarm Connection on each power supply provides status information on the condition of the supply. 9 Pin Dsubminiature Pin 6 NO Pin 6 shorts to Pin 7 when the Power Supply is Non-Operational Pin 7 COM Pin 8 NC Pin 8 shorts to Pin 7 when the Power Supply is Oper...

Page 5 - Control Modules; WEB; Telnet; Installation; controller provides the following connections:; Serial Port

K3 1RU AB Switch Page 5 Control Modules The K3 Series AB Switch System is available with three types of control modules; Network, Contact Closure, or Gang Control Expansion. One of three control options shown below will be installed in the chassis for remote control of the installed AB switch cards....

Page 7 - Setting the IP address using ARP; Delete the entry from the ARP cache by typing:; Setting IP Address with Telnet; Select Run...Telnet; The factory default password is:; PASS

K3 1RU AB Switch Page 7 Setting the IP address using ARP To set the IP address using ARP, connect the jack marked 10Base-T to your local Ethernet network and apply power to the unit. The computer used to set the IP address must be on the same physical network as the C-AB-16-R . ARP does not work acr...

Page 9 - IP Settings; Setting IP address via Serial Port; Utility setip.exe is available from Dataprobe’s website at; Setting other Parameters; Via the Serial Port (or telnet on the; Location Name; three AB card slot positions of the 16 displayed are used in the K3.; password then enter the new password twice as prompted.

K3 1RU AB Switch Page 9 Select 6 for IP Settings. The IP Settings Menu appears: IP Settings 1. IP Address 192.168.1.42 2. Subnet 255.255.255.0 3. Gateway 0.0.0.0 4. Web Port 80 5. Telnet Port 23 6. Message Port 9100 7. MTU 1024 8. Write Community Name private 9. Read Community Name public A. SNMP Ma...

Page 10 - K3 1RU AB Switch

K3 1RU AB Switch Page 10 Com Port: Set the Baud Rate and Character Format for the serial port. Baud rate choices are 9600, 19200, and 38400. Character format choices are 8N1, 7E1 and 7O1 (databits, parity, stop bit). The Default Serial Port Parameters are 9600, 8 Data Bits, No Parity, One Stop Bit (...

Page 11 - . By removing power to the the K3 chassis momentarily and; Operation

K3 1RU AB Switch Page 11 Note: After changing the IP Address, Web Port, Telnet Port or Com Port parameters, it is necessary to reboot the C-AB-16-R . By removing power to the the K3 chassis momentarily and then reconnecting the power source. Neither operation will alter the switch positions of any A...

Page 14 - Telnet and Serial Port; into your Telnet application program

K3 1RU AB Switch Page 14 A logout button is provided. Click this button to be instantly logged out. There is an automatic logout function if there is no activity for two minutes. You can also just close the browser; however you will not be able to log back in for two minutes. Telnet and Serial Port ...

Page 15 - SNMP Manager Control

K3 1RU AB Switch Page 15 SNMP Manager Control The C-AB-16-R allows for management via SNMP. The private MIB is available from the Dataprobe Web Site at: http://www.dataprobe.com/files/switch/k16/k16.mib MIB Outline and MIB Definitions can be found in Appendix A. Command Line and Direct TCP Messaging...

Page 16 - cr; Gang Control Expansion; R Gang Expansion Card; Expansion Connector Pinout; Pin Designation

K3 1RU AB Switch Page 16 cr = The ASCII carriage return character If the queried card has been disabled then no response will be transmited. In response to the Query All command, 16 response messages will be sent. All invalid commands will be ignored. No response even when responses are enabled. Gan...

Page 18 - Specifications; Switch Interfaces; Three 25 Pin D Subminiature, Female Connectors.; Physical

K3 1RU AB Switch Page 18 Specifications Switch Interfaces D25 Three 25 Pin D Subminiature, Female Connectors. 25 leads switched. Option for Pins 1 and 7 common and unswitched. RJ8 Three 8 position 8 wire RJ type Modular jacks, Rear Panel/Card Edge. All 8 leads switched. Support all RJ Configurations...

Page 19 - MIB Outine; three AB; Mib Tree

K3 1RU AB Switch Page 19 MIB Outine NOTE: The K3 Series AB Switch System use the same network control interface as our larger K16 Series. The same SNMP MIB interface is used with same values and commands .Only the 1 st three AB card slot positions of the 16 displayed are used in the K3. Displayed Sl...

Page 20 - MIB Definitions; This variable is not directly accessible.

K3 1RU AB Switch Page 20 MIB Definitions k16RackName 1.3.6.1.4.1.1418.1.1.1 This read/write variable is the name of the k16 nest. This variable can be programmed either via SNMP, Telnet or via serial port. It can contain printable characters and MUST not exceed 20 characters in length. k16CardTable ...

Page 21 - ok; Trap Definitions

K3 1RU AB Switch Page 21 k16PowerSupply1 1.3.6.1.4.1.1418.1.1.4 This read only variable returns the current status of the power supply 1 as an enumerated integer where: 1 = ok 2 = failed. k16PowerSupply2 1.3.6.1.4.1.1418.1.1.5 This read only variable returns the current status of the power supply 2 ...

Page 22 - TECHNICAL SUPPORT, RETURNS and WARRANTY; Authorized Dataprobe Reseller,; WARRANTY

K16 Series Standalone/ -R1 Mount Page 22 TECHNICAL SUPPORT, RETURNS and WARRANTY Dataprobe Technical Support is available 8:30AM to 5:30PM ET to assist you in the installation and operation of this product. To obtain Technical Support call our Tech Support Hotline at 201- 967-8788, or Email us at te...