Jet JSG-96 - Manuals - manualsarea.com

Page 3 - WARNING

3 WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. This disc/belt sander is intended to be used with wood and wood products only. Use of this disc/belt sander and a dust collector with metal prod...

Page 4 - SAND with the grain of the wood.

4 • ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. • REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. • USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or ris...

Page 5 - Grounding Instructions

5 Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the ev ent of a malfunction or breakdown, grounding prov ides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an ...

Page 7 - Read and understand the entire contents of; Unpacking

7 Contents of the Shipping Carton 1. Sander 1. Sanding Belt 1. Sanding Disc 2. Tables 1. Center Point 3. Handles 2. 5/16” Flat W ashers 1. Miter Gauge 1. Owner's Manual 1. W arranty Card Tools Required for Assembly 1. 13mm W rench or socket (stand) 1. 12mm W rench or socket (stand) WARNING Read and ...

Page 8 - Assembly; CAUTION; Machine is heavy! Use care when lifting out; Mov e the sander to a workbench or one of

8 Assembly CAUTION Machine is heavy! Use care when lifting out of the shipping carton and moving to a final location. Stand or bench must be stable enough to support weight of machine. 1. Mov e the sander to a workbench or one of JET’s optional stands. Bolt the unit firmly to hold in place. JET’s cl...

Page 9 - Sanding Belt Table Adjustment; Always disconnect the sander from the; Place a square on the sanding belt table

9 Sanding Belt Table Adjustment WARNING Always disconnect the sander from the power source before servicing or making any adjustments. Failure to comply may cause serious injury! 1. Place a square on the sanding belt table with one edge along the graphite pad, or sanding belt (Figure 4). 2. If the t...

Page 11 - Belt Tracking Adjustment; Secure the tracking lock by pushing the; Disc Table Adjustment

11 Belt Tracking Adjustment 1. Connect the machine to the power source. One time quickly turn the machine “ON” and “OFF”. This will allow you to v iew the belts tendency to run down the middle, to the right, or to the left. The belt should run centered on the sanding drums. Do not let the belt run o...

Page 12 - If the miter slot is not parallel loosen the two; Sanding Disc Replacement; wheel. Make sure the disc plate is clean.; Center Point

12 4. If the miter slot is not parallel loosen the two socket head cap screws (A, Fig. 13) and adjust for parallel. Tighten the two screws when the adjustment is complete. 5. Always maintain a gap of approximately 1/16” between the table edge and disc. Once the table is square and parallel to the di...

Page 14 - Sander will not start

14 Troubleshooting Trouble Possible Cause Solution Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 1. Check all plug connections 2. Replace fuse or reset circuit breaker 3. Replace cord Sanding belt does not come up to speed 1. Ex...

Page 15 - Disc Sander Assembly Breakdown

Page 16 - Index Part

16 Parts List For The JSG-96 Sander Disc Sander Assembly Index Part No. No. Description Size Qty. 1 .......... JSG96-101....................... Base .............................................................. ................................... 1 2 .......... JSG96-102....................... Moto...

Page 18 - Belt Sander Assembly Breakdown

Page 19 - Belt Sander Assembly

19 Belt Sander Assembly Index Part No. No. Description Size Qty. 1 .......... JSG96-201....................... Bracket .......................................................... ................................... 1 2 .......... TS-0208071 ..................... Hex Socket Cap Screw.....................

Page 21 - Open Stand Breakdown

Page 22 - JSG-96 Open Stand Assembly

22 JSG-96 Open Stand Assembly Index Part No. No. Description Size Qty. 1 .......... JSG96-401....................... Stand Top (front and rear, short).................... ................................... 2 2 .......... JSG96-402....................... Stand Top (left and right, long) ...............

Page 23 - Closed Stand Breakdown

Page 24 - Closed Stand Assembly

24 Closed Stand Assembly Index Part No. No. Description Size Qty. 1 .......... JSG96-301....................... Base .............................................................. ................................... 1 2 .......... JSG96-302....................... Lock Nut ..............................