Intellinet Network Solutions 524780 - Manuals

3 2 Hardware R e a r P a n e l Item Name Description Antenna A/B These antennas are 3dBi dipole antennas. Radio ON/OFF Position the switch to activate or deactivate the wireless functions. Reset / WPS Reset the router to factory default settings (clear all settings) or start the WPS function. Press ...

4 Front Panel On the router’s front panel, there are LEDs that inform you of the router’s current status, as explained below. LED Status Description On Router is switched on and correctly powered. POWER (Green) On Off Wireless LAN WPS is on. Wireless LAN is disabled. Blinking Wireless traffic is tra...

5 I n s t a l l a t i o n 1. Connect the router to your ADSL cable through the supplied RJ11 cable. 2. Connect the router to your PC, hub or switch by attaching the Ethernet cable to the LAN port of the router. 3. Connect the power adapter to the power jack on the rear panel of the router. 4. The AD...

6 3 Setup Wizard This router provides a Setup Wizard tool to configure the ADSL settings. This wizard collects some ISPs’ ADSL settings so that you can easily configure the router’s ADSL settings by only selecting the ISP vendor from the wizard. If you cannot find your ISP from the list in the wizar...

7 3. The wizard will run and try to search for the router. If the router is found, the wizard will guide you to Step 5.

8 4. If the router cannot be found, enter the IP address and the password of the router to search again. Click “Next” to continue. 5. The wizard will automatically select the country you are in by checking the language of the operating system in your computer and then advance to the Select ISP scree...

9 3.2 Automatically Set the ISP If you can find the ISP from the wizard, follow the procedures below to let the wizard set the ISP settings automatically. 1. Select the ISP of your ADSL service. 2. Enter the username and password that your ISP has provided to you, if needed. Click “Next.”

11 5. The wizard will try to connect to the ISP you have selected. If the connection fails, run the wizard to select the ISP again. 6. If you successfully connect to the ISP, you will see the screen below. To configure additional settings, click “Advanced Settings” to go the Web management of the ro...

12 5.3 Manually Set the ISP If you cannot find the ISP from the wizard, follow the steps below to set the ISP settings manually. Before configuring the ISP manually, check with your ISP (Internet service provider) as to what kind of service is provided, such as PPPoE, PPPoA or RFC1483/2684. Gather t...

14 4. Enter the username and password that your ISP has provided to you, if needed. Click “Next.” 5. Click “Save” to save the settings and reboot the router. 6. After saving and rebooting the router, the ISP settings are completed. The wizard will then help to set your computer to obtain an IP addre...

17 4 IP Address Setting To use the router to access the Internet, the PCs in the network must have am Ethernet adapter installed and be connected to the router either directly or through a hub or switch. The TCP/IP protocol of each PC needs to be installed, and the IP address of each PC has to be se...

18 5. Click “OK” to confirm the setting. Your PC will now obtain an IP address automatically from your router’s DHCP server. N O T E : Make sure that the router’s DHCP server is the only DHCP server available on your LAN. W i n d o w s X P 1. Click “Start” and select “Control Panel”; then double-cli...

19 5. Click “OK” to confirm the setting. Your PC will now obtain an IP address automatically from your router’s DHCP server. N O T E : Make sure that the router’s DHCP server is the only DHCP server available on your LAN. W i n d o w s 2 0 0 0 1. Click “Start” and select “Settings,” then click “Cont...

21 5 Web Management Configuration Once you have configured your PCs to obtain an IP address automatically, the router’s DHCP server will automatically give your LAN clients an IP address. By default, the router’s DHCP server is enabled so you can obtain an IP address automatically. Once your PC has ...

25 5.2 General Setup Start your Web browser and log on to the Web management interface of the router, then either click “General Setup” on the left menu or click the “General Setup” link at the upper-right corner of the Web management interface. 5 . 2 . 1 S y s t e m This screen includes the basic c...

28 Parameter Description LAN Check/un-check the services on the LAN column to allow/ disallow the services access from the LAN side. WAN Check/un-check the services on the WAN column to allow/ disallow the services access from the WAN side. WAN Port This field allows the user to specify the port cor...

34 When you finish, click “Apply Changes.” You’ll see the following message displayed on Web browser. Click “Continue” to save the settings made and go back to the Web management interface; click “Apply” to save the settings made and restart the router so the settings will take effect after it reboo...

38 Parameter Description Attain DNS Automatically Select this item if you want to use the DNS servers obtained from ISP. Set DNS Manually Select this item to specify up to three DNS IP addresses. When you finish, click “Apply Changes.” You’ll see the following message displayed on Web browser. Click...

40 to share routes because all Internet data from the network is sent to the same ISP gateway. You may want to configure RIP if any of the following circumstances apply to your network: • Your home network setup includes an additional router or RIP-enabled PC (other than this one). This router and t...

41 RIP Config Table The RIP you have configured will be listed in the table. If you want to delete some settings, select the settings and click “Delete Selected.” When you finish, click “Apply Changes.” You’ll see the following message displayed on Web browser. Click “Continue” to save the settings ...

42 Parameter Description Interface Name The interface name is “br0.” IP Address Enter the IP address of the ADSL router for the local user to access the router’s Web screen. By default, the IP address is 192.168.2.1 . Subnet Mask Enter the subnet mask of the ADSL router. By default, the subnet mask ...

46 5.2.3.4 ARP Table ARP is the Address Resolution Protocol. Its job is to match MAC addresses to IP addresses and vice versa (matching IP addresses to MAC addresses). This screen lists the IP addresses and the matched MAC addresses in the network. 5.2.3.5 Bridging You can enable/disable the Spannin...

48 Parameter Description Disable Wireless LAN Interface Check to deactivate the wireless function of the router. When this is activated, the router will not be an access point for other wireless clients to connect wirelessly. Band Select the radio band from one of the following options: • 2.4GHz(B):...

50 Parameter Description Authentication Type There are three authentication types: Open System, Shared Key and Auto. • Open System authentication is not required to be successful, as a client may decline to authenticate with any other particular client. • Shared Key is only available if the WEP opti...

53 5.2.4.3 Security This router provides complete wireless LAN security functions, including WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can protect your wireless LAN from illegal access. Make sure your wireless stations use...

54 WPA2 (AES) for data encryption. The actual selection of the encryption methods will depend on the clients. Use 802.1x Authentication IEEE 802.1x is an authentication protocol. Every user must use a valid account to log in to this wireless router before accessing the wireless LAN. The authenticati...

55 RADIUS Server password of the external RADIUS server. When you finish, click “Apply Changes.” You’ll see the following message displayed on Web browser. Click “Continue” to save the settings made and go back to the Web management interface; click “Apply” to save the settings made and restart the ...

56 clients. If you enable this function, set the MAC address of the wireless clients that you want to filter. Disable disables this function. Allow Listed only allows the wireless clients with the MAC address you have specified access to the router. Deny Listed means the wireless clients with the MA...

62 Forwarding Table select the items and click “Delete Selected.” To remove all settings, just click “Delete All.” When you finish, click “Apply Changes.” You’ll see the following message displayed on Web browser. Click “Continue” to save the settings made and go back to the Web management interface...

63 Parameter Description Disabled/Enabled Click the radio button to enable or disable the feature. If disabled, all interfaces belong to the default group. Interface groups To manipulate a mapping group: 1. Select a group from the table. 2. Select interfaces from the available/grouped interface list...

64 Click “Continue” to save the settings made and go back to the Web management interface; click “Apply” to save the settings made and restart the router so the settings will take effect after it reboots. 5.2.6.3 UPNP When the UPnP function is enabled, the router can be detected by UPnP-compliant sy...

65 5.2.6.4 IGMP Proxy When IGMP Proxy (Internet Group Management Protocol Proxy) is enabled, the router can make intelligent multicast forwarding decisions by examining the contents of each frame’s IP header. Without the function, the router will broadcast the multicast packets to each port and may ...

68 5.2.7.2 MAC Filtering The MAC Filtering feature allows you to define rules to allow or deny frames through the router based on source MAC address, destination MAC address and traffic direction. Parameter Description Outgoing Default Action Specify the default action on the LAN-to-WAN (Traffic-to-...

69 Source MAC Address This must be in 12-digit hexadecimal format; for example, “00-d0-59-c6-12-43.” Destination MAC Address This must be in 12-digit hexadecimal format; for example, “00-d0-59-c6-12-50.” Current Filter Table To remove some filter rules from the Current Filter Table, select the MAC a...

75 Click “Continue” to save the settings made and go back to the Web management interface; click “Apply” to save the settings made and restart the router so the settings will take effect after it reboots. 5.2.7.7 DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular...

79 5.4 Tools The Tools section includes the basic configuration tools, such as Back Up, Restore Configuration Settings, Upgrade System Firmware and Diagnostic Test. 5 . 4 . 1 C o n f i g u r a t i o n T o o l s This screen allows you to back up the current settings to a file or restore the settings ...

80 Load Settings from File Click “Browse” to search for a file you saved before, and click “Upload” to restore the saved configuration. Restore Settings to Default Click “Reset” to force the router to perform a power reset and restore the original factory settings. 5 . 4 . 2 F i r m w a r e U p g r ...

81 5 . 4 . 4 A T M L o o p b a c k In order to isolate ATM interface problems, you can use ATM OAM loopback cells to verify connectivity between VP/VC endpoints, as well as segment endpoints within the VP/VC. This screen allows you to use ATM ping to test the reachability of a segment endpoint or a ...

82 5 . 4 . 5 D i a g n o s t i c T e s t The Diagnostic Test screen shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. 5 . 4 . 6 R e b o o t Whenever you use the Web configuration to change system settings, the changes are initially place...

83 6 Troubleshooting The LAN LED on the front panel does not light up. STEPS CORRECTIVE ACTION 1 Check the Ethernet cable connections between your router and the computer or hub. 2 Check for faulty Ethernet cables. 3 Make sure your computer’s Ethernet card is working properly. 4 If these steps fail ...

85 I forget my login username and/or password. STEPS CORRECTIVE ACTION 1 If you have changed the password and have now forgotten it, you will need to upload the default configuration file. This will erase all custom configurations and restore all of the factory defaults, including the password. 2 Pr...

86 Initialization of the ADSL connection failed. STEPS CORRECTIVE ACTION 1 Check the cable connections between the ADSL port and the wall jack. The ADSL LED on the rear panel of the router should be on. 2 Check that the VPI, VCI, Type of Encapsulation and Type of Multiplexing settings are the same a...

87 7 Glossary 10Base-T It is an Ethernet standard for a local area network (LAN). 10Base-T uses a twisted pair cable with a maximum length of 100 meters. AAL ATM is an adaptation layer that defines the rules governing segmentation and reassembly of data into cells. Different AAL types are suited to ...

92 8 S p e c i f i c a t i o n s S t a n d a r d s • IEEE 802.3 (10Base-T Ethernet) • IEEE 802.3u (100Base-TX Fast Ethernet) • IEEE 802.11b (11 Mbps Wireless LAN) • IEEE 802.11g (54 Mbps Wireless LAN) • IEEE 802.11n Draft 2.0 (300 Mbps Wireless LAN) • ADSL2+ (ITU G.992.5) up to 24 Mbps • ADSL2 (ITU ...

93 - URL filter • Supports UPnP (Universal Plug and Play) • Supports DHCP (client/server) • Supports VPN PPTP, L2TP and IPsec passthrough W i r e l e s s • Chipset: Realtek RTL8192SU • Wireless frequency range: 2.4 – 2.4835 GHz • Modulation technologies: - 802.11b: Direct Sequence Spread Spectrum (D...

95 W A S T E E L E C T R I C A L & E L E C T R O N I C E Q U I P M E N T Disposal of Electric and Electronic Equipment (applicable in the European Union and other European countries with separate collection systems) ENGLISH This symbol on the product or its packaging indicates that this product ...

97 W A R R A N T Y I N F O R M A T I O N ENGLISH: For warranty information, go to www.intellinet-network.com/warranty. DEUTSCH: Garantieinformationen finden Sie unter www.intellinet-network.com/warranty. ESPAÑOL: Si desea obtener información sobre la garantía, visite www.intellinet-network.com/warra...

98 All products mentioned are trademarks or registered trademarks of their respective owners. Copyright © INTELLINET NETWORK SOLUTIONS