Intellinet Network Solutions 523868 - Manuals

Page 3 - introduction; Package Contents; to correct the interference at the user’s own expense.; CE

introduction Thank you for purchasing the INTellINeT NeTWoRK SolUTIoNS ™ Managed layer 3 Access Switch, Model 523868.This is a high-performance managed SNMP switch that provides users with 24 10/100 Mbps ethernet and four Gigabit combo ports. The Web/SNMP management provides remote control capabilit...

Page 4 - tabLe of contents; Configuration Using Telnet and SSH

tabLe of contents Introduction & FCC Warning ........................................................................................... 3 1 HARdWARe ................................................................................................................. 6 1.1 Front Panel Connections &a...

Page 6 - hardware; front Panel connections & indicators; utilizes ports with copper and SFP fiber port connectors; Unit LED

1 hardware 1.1 front Panel connections & indicators The Managed layer 3 Access Switch utilizes ports with copper and SFP fiber port connectors functioning under ethernet/Fast ethernet/Gigabit ethernet standards. 1.1.1 10/100base-tX Ports The 10/100Base-TX ports ( 1 above) support network speeds ...

Page 7 - in the Specifications section.; Port LED; Flashing (green) Data traffic passing through port

7 INSTALLATION 1.2 installation 1.2.1 Location/Position The location of the switch can greatly affect its performance. Consider these guidelines before placement, connection and operation. • Choose a location that complies with the acceptable temperature and humidity ranges listed in the Specificati...

Page 8 - Installing the SFP Modules and Fiber Cable; plugs that may be present in the SFP module’s mouth.; switch ManageMent/oPeration; This system can be managed three ways:

1.2.3 Installing the SFP Modules and Fiber Cable 1. Slide the selected SFP module into one of the four Gigabit SFP slots below the RS-232 port, making sure the SFP module is aligned correctly with the inside of the slot. 2. Insert and slide the module into the SFP slot until it clicks into place, re...

Page 15 - Status

2.2.3 Physical interface Physical Interface on the Config Menu displays Ethernet port status in real time. Two options are available: Configure the port in the fields in the Interface Configuration window; and check the results in the Runtime Status window. 2.2.3.1 Interface Configuration Port: Sele...

Page 22 - Parameters

2.2.7.1.1 STP Status This screen lets you enable or disable STP. Modes: Three modes are available in the drop-down menu: “STP,” “RSTP” (Rapid STP) and “MSTP” (Multiple STP). If MSTP is enabled, the following four attributes are enabled at the same time. Region Name: This is an alphanumeric configura...

Page 30 - First Come First Service:

serviced. You can use the strict priority queue for mission-critical and time-sensitive traffic. There are three options. First Come First Service: The first-come frame has the highest priority. High First: A packet’s priority depends on its CoS value. Weighted Round Robin (WRR): If WRR scheduling a...

Page 34 - Control; Authentication Method:

2.2.9.2 Filter Attach A filter set is idle if you did not attach it to any ingress port. Use this screen to attach a filter set to ingress ports. Click “Attach All” to apply the filter set to all the ports of the system. Click “Detach All” to remove all the filters from the attached ports. Click “Su...

Page 37 - command Line interface; Although the commands are helpful in some situations, it is

2.2.11.3 History Chart display information for different ports and statistics items on this chart. Since this shows the history of the statistics information, the line chart keeps the old data even when it is refreshed. 2.2.12 Save Configuration Click “Save” to make the settings permanent by saving ...

Page 41 - command to create a vlan entry with a string on the Switch.

status of the port. CLI Syntax: auto-negotiation Example: (config)# interface gi1/0/2 (config-if)# auto-negotiation This example shows how to use the auto-negotiation configuration command on the switch to enable the auto-negotiation mode. 2.3.3.4.2 Interface Duplex Use the duplex configuration comm...

Page 50 - sPecifications; Standards

2.3.3.27.2 Clear Port Security This command is used to clear port security dynamic MAC addresses. CLI Syntax: clear port-security dynamic [address MAC] | [interface IFNAME] Example: SWITCH# clear port-security dynamic SWITCH# clear port-security dynamic address 0023.1313.2313 SWITCH# clear port-secu...

Page 51 - Configuration Options; • Full and half duplex per Fast Ethernet port; LEDs

• Packet filter/forwarding rate: - 1,488,000 pps (1000 Mbps) - 148,800 pps (100 Mbps) - 14,880 pps (10 Mbps) • Buffer memory: 32 MBytes • MAC address table: 16384 entries • Backplane speed: 12.8 Gbps • Switch architecture: store and forward • Ports - 24 x RJ-45 Fast Ethernet ports - 4 RJ-45 Gigabit ...