InFocus infocus single stud short throw wall mount - Manuals

Page 2 - Installation Instructions; DISCLAIMER

PRJ-WALLKIT-11 Installation Instructions 2 Visit the InFocus support site at www.infocus.com/support DISCLAIMER InFocus and its affiliated corporations and subsidiaries(collectively "InFocus"), intend to make this manual accurateand complete. However, InFocus makes no claim that theinformati...

Page 3 - LEGEND

Installation Instructions PRJ-WALLKIT-11 Visit the InFocus support site at www.infocus.com/support 3 LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de ...

Page 4 - TOOLS REQUIRED FOR INSTALLATION

PRJ-WALLKIT-11 Installation Instructions 4 Visit the InFocus support site at www.infocus.com/support TOOLS REQUIRED FOR INSTALLATION PARTS 1/2" (12.7mm) #2 7/32" (5.6mm) 3/8" (9.5mm) 5/32" 1/2" (12.7mm) 7/16" (11.2mm) (security)[included] S (4) M (2) A (1) R (4) 1/4-20 x 3/8&...

Page 5 - Site Requirements

Installation Instructions PRJ-WALLKIT-11 Visit the InFocus support site at www.infocus.com/support 5 Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for install...

Page 6 - ASSEMBLY AND INSTALLATION; Installing Mounting Bracket; Mounting Wall Bracket; Concrete or Concrete Block; Figure 1

PRJ-WALLKIT-11 Installation Instructions 6 Visit the InFocus support site at www.infocus.com/support ASSEMBLY AND INSTALLATION The single stud short throw wall mount can be mounted toconcrete, concrete block, 2" x 4" wood studs or steel studs. Installing Mounting Bracket WARNING: ELECTRICAL ...

Page 7 - See

Installation Instructions PRJ-WALLKIT-11 Visit the InFocus support site at www.infocus.com/support 7 5. Install three 5/16 x 2-1/2" hex head lag screws (P) throughthree 5/16" washers (Q), inner holes of wall bracket (B) andinto drilled holes. (See Figure 4) Figure 4 Steel Studs IMPORTANT ! :...

Page 8 - Figure 9; Installation to Wall Bracket

PRJ-WALLKIT-11 Installation Instructions 8 Visit the InFocus support site at www.infocus.com/support 10. Place wall bracket (B) over anchors and align mounting holes in display mount with holes in anchors. (See Figure 9) 11. Insert 1/4-20 x 1-3/4" Phillips pan head screws (F) through 1/4" wa...

Page 9 - Installing Mount Covers; Projector Installation; Projector Mount Installation; If projector mount is NOT installed in the

Installation Instructions PRJ-WALLKIT-11 Visit the InFocus support site at www.infocus.com/support 9 Installing Mount Covers 1. Raise lower cover (D) up to wall mount assembly. (SeeFigure 12) Figure 12 2. Lower top cover (C) onto wall mount assembly. (SeeFigure 13) 3. Install two #10 x 1" Philli...

Page 10 - Projector Installation to Mount; Projector Mount Adjustments; Yaw Adjustment

PRJ-WALLKIT-11 Installation Instructions 10 Visit the InFocus support site at www.infocus.com/support Projector Installation to Mount WARNING: IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUSPERSONAL INJURY OR DAMAGE TO EQUIPMENT. DONOT substitute hardware. Use only the hardw...

Page 11 - Pitch Adjustment; Pitch; Roll Adjustment

Installation Instructions PRJ-WALLKIT-11 Visit the InFocus support site at www.infocus.com/support 11 Pitch Adjustment NOTE: Pitch can be adjusted using the projector mount or the pitch of the entire arm can be adjusted. See Pitch Adjustment - Entire Arm section for details. 1. Loosen Pitch adjustme...

Page 12 - Pitch Adjustment - Entire Arm; or

PRJ-WALLKIT-11 Installation Instructions 12 Visit the InFocus support site at www.infocus.com/support Pitch Adjustment - Entire Arm 1. Loosen two 5/16-18 x 1/2" hex head screws (T) (one oneach side of wall bracket). (See Figure 22) 2. Loosen two bolts (one on each side of pitch adjustmentscrew)....

Page 13 - Extension Adjustment

Installation Instructions PRJ-WALLKIT-11 Visit the InFocus support site at www.infocus.com/support 13 3. (Optional) Cables can be tied to inside of projector’s front cover using cable ties (not included). Route cables nearfront cover and wrap cable tie through slots on front coverand around cables. ...

Page 16 - InFocus Corporation