InFocus IN5542C - Manuals

InFocus IN5542C – Manual in PDF format online.

Manuals:

Manual

Manual InFocus IN5542C

Summary

Page 2 - Initial set signals; POSITION in the IMAGE menu.; Data

2 Initial set signals Initial set signals The following signals are used for initial settings. The signal timing for some computer models may be different. In this case, adjust the V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Display time...

Page 3 - MONITOR OUT; At RGB signal; COMPONENT VIDEO

3 Connection to the ports A COMPUTER IN1, B COMPUTER IN2, C MONITOR OUT D-sub 15pin mini shrink port • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level At RGB signal Pin Signal Pin Signal 1 V...

Page 5 - HDMI

5 I O HDMI DVI-D CONTROL IN CONTROL OUT REMOTE CONTROLIN OUT S-VIDEO COMPUTER IN2 COMPUTER IN1 VIDEO 1 BNC R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2 Y Cb/Pb Cr/Pr AC IN LAN MONITOR OUT Connection to the ports (continued) Q P O O HDMI • Type :Digital video connector Pin Signal Pin Signal Pin Signal 1 T.M.D.S. ...

Page 6 - PJLink command; This projector is equipped with PJLink; protocol

6 PJLink command PJLink command Commands Control Description Parameter or Response POWR Power Contorol 0 = Standby1 = Power On POWR ? Power Status inquiry 0 = Standby1 = Power On2 = Cool Down INPT Input Source selection 11 = COMPUTER IN 112 = COMPUTER IN 213 = BNC21 = COMPONENT22 = S-VIDEO23 = VIDEO...

Page 7 - NOTE

7 PJLink command (continued) Commands Control Description Parameter or Response LAMP ? Lamp Status inquiry 1st number (digits 1 to 5): Lamp Time2nd number : 0 = Lamp off, 1 = Lamp on INST ? Input Source List inquiry 11 12 13 21 22 23 24 31 32 NAME ? Projector Name inquiry Responds with the name set ...

Page 8 - RS-232C Communication; Connecting the cable

8 RS-232C Communication RS-232C Communication 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) RTS CTS (8) (8) DTS - (9) (9) RI Connect...

Page 9 - • Commands are not accepted during warm-up.

9 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+‘00H’ +‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the...

Page 10 - Communication Port; The following two ports are assigned for command control.; Command Control Settings; Port Settings; and

10 Command Control via the Network Communication Port The following two ports are assigned for command control. TCP #23 TCP #9715 Command Control Settings Configure the following items from a web browser when command control is used. Command Control via the Network Port Settings Network Control Port...

Page 11 - Command Format; Requesting projector status (Get command)

11 Command Control via the Network (continued) Command Format [TCP #23] 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low: Lower byte of CRC flag for command data CRC_high: Upper byte of CRC flag for command data 3. Command...

Page 12 - Decreasing the projector setting value (Decrement command); ‘xxxxH’; When authentication error occurred.; is sent

12 Command Control via the Network (continued) Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector. Header + Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’) (2) The projector decreases the setting value on the above ...

Page 13 - ‘xxH’; Automatic Connection Break; • During the transmission of the second or subsequent commands, the

13 7. Reply Data The connection ID (the data is same as the connection ID data on the sending data format) is attached to the Network control commands reply data. ACK reply: ‘06H’ + ‘xxH’ NAK reply: ‘15H’ + ‘xxH’ Error reply: ‘1CH’ + ‘xxxxH’ + ‘xxH’ Data reply: ‘1DH’ + ‘xxxxH’ + ‘xxH’ Projector busy...

Page 14 - Communications setting; (3) Get the number of connected projectors; Protocol; Data chart; Daisy Chain Communication; Transmitting side

14 Daisy Chain Communication 1.Communications setting Set the same communication settings (selecting from options below) on the CONTROL terminal for transmitting and receiving side connected with a RS-232C cable. Baud rate: 4800 / 9600 / 19200 / 38400 bps Parity NONE / ODD / EVEN Data bit: 8 bit (fi...

Page 15 - Calculation of Checksum; Header; Group and ID Settings; identification and ID.; note

15 Daisy Chain Communication Calculation of Checksum Sum up all of 12 bytes except the Checksum, then make the bit inversion of the lowest byte of the total, and add 1 to the inverted byte. The calculated result is the Checksum data. Exp. Communication Group: A / Communication ID: 1 Header data (7 b...

Page 16 - Command data; Controlling projector

16 Daisy Chain Communication Command data ① Controlling projector byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action Type Setting Code low high low high low high Action (byte_0-1) Action Classification Content 1 Set Change setting to desired value. 4 Increment Increment setup value by 1. 5 Decrement D...

Page 17 - Error Code

17 Daisy Chain Communication Command data Requesting projector status (Get command) (1) Send the following request code from the PC to the projector. Header + Command data (‘02H’ + ‘00H’ + type (2 bytes) + connection ID (2 bytes)) (2) The projector returns the response code to the PC. ‘9DH’ + ‘02H’ ...

Page 18 - Get the number of connected projectors; (1) Send the following request code from the PC to the projector.; Set the communication Group identification and; (1) Send the following setting code from the PC to the projector.

18 Daisy Chain Communication Get the number of connected projectors (1) Send the following request code from the PC to the projector. Header + Command data (‘02H’ + ‘00H’ + ‘00H’ + ‘00H’ + connection ID (2 bytes)) (2) The projector returns the response code to the PC. ‘9EH’ + ‘04H’ + connection ID (...

Page 19 - Get the communication Group identification and; • During transmission of the second or subsequent commands, the

19 Daisy Chain Communication Get the communication Group identification and Communication ID (1) Send the following request code from the PC to the projector. Header + Command data (‘02H’ + ‘00H’ + target number (2 bytes) + connection ID (2 bytes)) (2) The projector returns the response code to the ...

Page 20 - RS-232C Communication / Network command table

20 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code RS-232C Communication / Network command table Power Set OFF BE EF 03 06 00 2A D3 01 00 00 60 00 00 ON BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 19 D3 02 00 00 60 00 ...