Infinity TSS-SAT4000 - Manuals

Page 2 - Table of Contents; WNER

2 TSS-SAT4000 3 Introduction 4 Planning Your System 4 Placement 5 Installation 5 Tabletop/Shelf Placement Assembly 8 Wall-Mounting the TSS-SAT4000 Using the Included Wall Bracket 9 Wiring the Speaker 10 Specifications Table of Contents TSS-SAT4000 O WNER ’ S G UIDE INFP1595Sat4000-OM 10/18/04 2:41 P...

Page 3 - NTRODUCTION; Infinity Total Solutions

3 TSS-SAT4000 (1) Satellite Speaker (1) Medium Collar (1) Pan-Head Phillips Screw 1/4-20 x 3/4" (2) Pan-Head Phillips Screws 1/4-20 x 1" (1) Flat-Head Phillips Screw1/4-20 x 1-1/4" (6) Flat-Head Phillips Screws1/4-20 x 7/8" (1) Large Collar (1) Allen Wrench (3) 1/4-20 Flat Washers (3...

Page 4 - LACEMENT; Left and Right Front Channels

4 TSS-SAT4000 P LANNING Y OUR S YSTEM Before deciding where to best place your speakers, survey yourroom and study Figures 1 and 2. Figure 1. In this overhead view of a typical 5-channel installation,satellite speakers are used to reproduce sound for the front and surround channels. The center chann...

Page 5 - NSTALLATION; Tabletop/Shelf Placement Assembly

5 TSS-SAT4000 I NSTALLATION Please read through this owner’s guide completely beforeattempting to install or connect the speakers. We understand thatyou may be anxious to play your new system, so we have madeevery effort to simplify the installation and connections of theTSS-SAT4000. Before proceedi...

Page 6 - Step Three; Step Four; Step Two

6 TSS-SAT4000 1/4-20 x 1-1/4"Flat-Head Screw Step Three For Small Table Stand Assembly Assemble the table stand plate, the small section and the foot.Place three nuts (provided) in base of foot and secure them in place by three screws (provided) through the top of the table stand plate. Step Fou...

Page 7 - Step Five

7 TSS-SAT4000 Step Four For Medium and Large Table Stand Assembly Use screw and washer to attach medium or large base assembly to the speaker assembly, as shown. (3) 1/4-20 x 7/8"Flat-Head Screws (3) 1/4-20 x 7/8"Flat-Head Screws 1/4-20 x 1" Pan-Head Screw Flat Washer Flat Washers 1/4-20...

Page 9 - Step Six; Surround Modes; Wiring and Polarity

9 TSS-SAT4000 Step Six The wall-bracket design allows for rotation of the speakers at angles up to 30 degrees of center. Position the speakers so they face toward the primary listening position, before fully tightening. Figure 3. This example shows how to connect bare wires to theterminals. Banana p...

Page 10 - PECIFICATIONS; PTIONAL

10 TSS-SAT4000 S PECIFICATIONS TSS-SAT4000 Frequency Response 120Hz – 20kHz (±3dB) Nominal Impedance 8 ohms Sensitivity 89dB (2.83V @ 1m) Recommended Amplifier 10 – 150 watts Power Range Crossover Frequencies 1,000Hz, 3,800Hz; 24dB/octave Low-Frequency Drivers ( 4) 3-1/2" (89mm) MMD, ® magnetica...

Page 11 - OTES

11 TSS-SAT4000 N OTES INFP1595Sat4000-OM 10/18/04 2:42 PM Page 11