Infinity TOTAL SPEAKER SOLUTIONS - Manuals

Page 3 - Table of Contents; WNER

3 TSS-1200 (120V) 2 Important Safety Precautions 4 Introduction 4 Unpacking the System 4 Planning Your System 5 Placement 5 Wall-Mounting the Satellites and Center Channel 7 Center and Satellite Speaker Connections 8 Subwoofer Controls 9 Subwoofer Connections 10 Operation 10 Maintenance and Service ...

Page 4 - Infinity Total Solutions; NPACKING THE; NTRODUCTION; LANNING; (5) Wall brackets for satellites and center channel

Infinity Total Solutions ™ Infinity Total Solutions continues Infinity’s longstanding commitmentto accurate sound reproduction. Our proprietary Metal MatrixDiaphragm ™ (MMD ® ) drivers, precision dividing networks and rigid, well-braced enclosures combine to deliver uncompromisedperformance in any s...

Page 5 - LACEMENT; Mounting on Floor Stands; IMPORTANT SAFETY NOTE:; ALL

5 TSS-1200 (120V) Left and Right Front Channels For left and right front channels, place one satellite to the leftand another to the right of the television, as shown in Figure 1.Since the speakers are magnetically shielded, you can placethem very close to the TV without worrying about the magneticf...

Page 6 - Adjustable Wall Bracket

6 TSS-1200 (120V) Adjustable Wall Bracket Step 1. Remove the rear foot by loosening the screw on the bottom of the satellite. Step 2. Mark the positions on the wall where you would like to place the mounting screws. Step 3. Place bracket against the wall and fasten four 1-1/2" #10 wood screws th...

Page 7 - Turn Off All Power

7 TSS-1200 (120V) C ENTER AND S ATELLITE S PEAKER C ONNECTIONS Turn Off All Power After placing the speakers, you are ready to connect your system.First, turn off all audio-system power. Use high-quality speakerwire to make your connections. #18-gauge speaker wire withpolarity coding is included. Fo...

Page 8 - Rear Panel; LEVEL; POWER; CAUTION; A Few Suggestions; The volume control setting on your processor/preamp or receiver

8 TSS-1200 (120V) S UBWOOFER C ONTROLS Rear Panel CROSSOVERFREQUENCY LEVEL LINE LEVEL IN PHASE Min Max L R For LFE use L or R LFE NORMAL POWER 50Hz 80Hz 0˚ 180˚ 150Hz CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ON OFF NRTL/C CSA22.2 UL1492 ® ® WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO...

Page 9 - OT; If you have a Dolby; subwoofer

9 TSS-1200 (120V) S UBWOOFER C ONNECTIONS If your receiver/processor does not contain a Dolby Digital or DTS processor but has asubwoofer output: Set line-level/LFE switch to “Normal.” N NO OT TEE: If your receiver/processor has only one sub out, you may use either the L or R input. If you have a Do...

Page 10 - PERATION; Surround Modes; Power On; Final Positioning; AINTENANCE AND

10 TSS-1200 (120V) O PERATION Surround Modes When using the system in a Dolby Digital or DTS home theatersystem, make sure all speakers are set to “Small”. When using theTSS-1200 in a Dolby Pro Logic ® home theater system, make sure the receiver’s center channel mode is set to “Normal.” Some Dolby D...

Page 11 - PECIFICATIONS; Satellites; Powered Subwoofer

S PECIFICATIONS 11 TSS-1200 (120V) TSS-1200 Satellites Center Channel Frequency Range: 120Hz – 20,000Hz (±3dB) 120Hz – 20,000Hz (±3dB) RecommendedAmplifier Power Range: 10 – 125 Watts 10 – 125 Watts Sensitivity: 89dB 89dB (2.83V @ 1 meter) Nominal Impedance: 8 Ohms 8 Ohms Crossover Frequency: 3,500H...