Page 2 - CONTENTS; ELECTRICAL PARTS LIST ........................ ......................................11; Satellites & Center Channel
CONTENTS BASIC SPECIFICATIONS . . . . . . . . . ………………………………………….1 DETAILED SPECIFICATIONS . . . . . . . . . . . ………………………………….2 CONTROLS. ………………….. .. . …………………………………... . . . . . . .4 CONNECTIONS . . . . . . . . . . . ……….………………………………..…. . . . 5 OPERATION……. . . . . .. . . . . . . . .. .. . . . ....
Page 5 - A Few Suggestions; UBWOOFER; Rear Panel; LEVEL; LINE LEVEL IN; L R; For LFE use L or R; POWER; C A U T I O N; ON
A Few Suggestions We recommend that you do not operate your speakers orsubwoofer with the bass, treble and loudness controls set to full boost. This will place undue strain on your electronics andspeakers and could damage them. The volume control setting on your processor/preamp or receiver is not a...
Page 6 - If you have a Dolby* Digital or DTS; subwoofer
TSS-1100 S UBWOOFER C ONNECTIONS If your receiver/processor does not contain a Dolby Digital or DTS processor but has asubwoofer output: Set line-level/LFE switch to “Normal.” NOTE: If your receiver/processor has only one sub out,you may use either the L or R input. If you have a Dolby* Digital or D...
Page 7 - PERATION; Surround Modes; Power On; Final Positioning; AINTENANCE AND
O PERATION Surround Modes When using the system in a Dolby Digital or DTS home theatersystem, make sure all speakers are set to “Small”. When using theTSS-1100 in a Dolby Pro Logic* home theater system, make surethe receiver’s center channel mode is set to “Normal.” Some Dolby Digital-equipped recei...
Page 8 - SERVICE NOTE; ) Carefully pry metal grille out of its recess with a sharp pointed
SERVICE NOTE Access to woofer: 1) Carefully pry metal grille out of its recess with a sharp pointed instrument such as an awl or dental pick – USE CAUTION and protect the surface of the subwoofer from scratches or dents from the work tool. Work evenly around the perimeter until the grill w/ gasket c...
Page 10 - Switches/knobs on the amplifier faceplate:
TSS1100 sub Test Set Up and Procedure SYSTEM AURAL SWEEP TEST Equipment needed: • Function/signal generator/sweep generator • Multimeter • RCA cables General Unit Function (UUT = Unit Under Test) Switches/knobs on the amplifier faceplate: Crossover Frequency Adjust full CW (150Hz) Phase switch – eit...
Page 12 - MAIN PCB
TSS-1100 120V ELECTRICAL PARTS LIST Part Number Qty Description Reference Designator MAIN PCB Resistors 020-000098-400 4 Carbon film resistor 0R 1/8W C22-C24,31 020-220497-120 1 Carbon film resistor 2K2 1/4W J R11 021-100401-120 1 MOF Resistor 1K 1W J Kink R103 021-220202-120 1 MOF Resistor 22R 2W(S...
Page 14 - Miscellaneous
MAIN PCB 054-540100-100 3 SMD Transistor (PNP) PN:MMBT5401 LT1 Q20,24,26 THERMAL SENSE PCB 024-100598-120 3 SMD Resistor 10K 1/8W J 0805 R138-R141 024-560498-120 1 SMD Resistor 5K6 1/8W J 0805 R140 031-100344-100 4 0U1/50V K 0805 X7R C81-82, C13,C38 054-007200-100 1 SMD IC TL072CDR SO-8 U8 054-39040...
Page 18 - THERMAL SENSE PCB