Ikea IGS900DS01 - Manuals

6 Electrical Requirements IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.If codes permit and a separate ground wire is used, it ...

7 Flexible metal appliance connector: ■ If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, ½" (1.3 cm) or ¾" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line. ■ A ½" (1.3 cm) male pipe thread is ne...

8 Install Anti-Tip Bracket 1. Remove the anti-tip bracket that is taped inside the upper oven with the package containing literature. 2. Determine which mounting method to use: floor or wall.If you have a stone or masonry floor, you can use the wall mounting method. 3. Determine and mark edge of ran...

9 3. Use a 15 / 16 " combination wrench and an adjustable wrench to attach the flexible connector to the adapters. IMPORTANT: All connections must be wrench-tightened. Do not make connections to the gas pressure regulator too tight. Making the connections too tight may crack the regulator and ca...

10 3. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, stop tilting the range and lower it gently back to the floor. The range foot is not engaged in the anti- tip bracket. IMPORTANT: If there is a snapping or popping sound when lifting the range, the range ...

11 Check Operation of Both Oven Bake Burners 1. Press BAKE for the desired oven.“BAKE” scrolls down in the upper text display area or scrolls up in the lower text display area, depending on oven selection, and 350°F is displayed. After 3 seconds “Set temp” scrolls in the selected oven text display a...

12 GAS CONVERSIONS Gas conversions from Natural gas to LP gas or from LP gas to Natural gas must be done by a qualified installer. WARNING Explosion Hazard Use a new CSA International approved gas supply line.Install a shut-off valve.Securely tighten all gas connections.If connected to LP, have a qu...

13 2. Unscrew the regulator cap and remove the plastic cover. 3. Flip the regulator cap over and replace the plastic cover. 4. Screw the regulator cap securely back into place. Do not overtighten. To Convert Oven Bake Burners (Natural Gas to LP) To Convert Lower Oven Bake Burner:1. Remove oven racks...

14 9. Turn the Number 0.070 Natural gas orifice hood counterclockwise to remove. 10. Install the Number 0.044 LP gas orifice hood, turning it clockwise 4 or 5 turns. Do not overtighten. 11. Position the oven bake burner over the orifice hood and reinstall using screw. To Convert Upper Oven Bake Burn...

15 5. Place the broil burner on the broil burner orifice hood. Insert the broil burner locator pin in the hole in the oven back. 6. Position the broil burner against the roof of the oven cavity and attach with screw. To Convert Surface Burners (Natural Gas to LP) 1. If the burner grates are installe...

16 To Convert Gas Pressure Regulator (LP to Natural Gas) 1. Locate gas pressure regulator at the rear of the range. IMPORTANT: Do not remove the gas pressure regulator. 2. Unscrew the regulator cap and remove the plastic cover. 3. Flip the regulator cap over and replace the plastic cover. 4. Screw t...

17 8. Unscrew and remove the cover over the orifice. 9. Turn the Number 0.044 LP gas orifice hood counterclockwise to remove. 10. Install the Number 0.070 Natural gas orifice hood, turning it clockwise 4 or 5 turns. Do not overtighten. A A. Orifice cover A A. Number 0.044 LP gas orifice hood A .070 ...

18 3. Turn the green Number 0.037 LP gas broil burner orifice hood counterclockwise to remove. 4. Install the Number 0.054 Natural gas broil burner orifice hood, turning it clockwise 4 or 5 turns. Do not overtighten. 5. Place the broil burner on the broil burner orifice hood. Insert the broil burner...