IBM S84H-4552-00 - Manuals - manualsarea.com

Page 3 - IBM Mobile Systems; IBM

S84H-4552-00 IBM Mobile Systems Hardware Maintenance ManualSelectaDock II Supplement November 1996 Use this supplement with theIBM Mobile SystemsHardware Maintenance Manual IBM

Page 4 - ii; IBM Mobile Systems HMM

Note Before using this information and the product itsupports, be sure to read the general informationunder “Notices” on page 56. First Edition (November 1996) The following paragraph does not apply to the UnitedKingdom or any country where such provisions areinconsistent with local law: INTERNATION...

Page 5 - Copyright IBM Corp. 1996; iii

ThinkPad SelectaDock DockingSystem  Copyright IBM Corp. 1996 iii

Page 6 - iv

Page 7 - Contents; ThinkPad SelectaDock Docking System

Contents ThinkPad SelectaDock Docking System . . . . . iii Read This First . . . . . . . . . . . . . . . . . . 1 General Preparation . . . . . . . . . . . . . . . . 3 Checkout Guide . . . . . . . . . . . . . . . . . 4 How to Run the Diagnostics . . . . . . . . . . . . 11 Symptom-to-FRU Index . . . ....

Page 9 - Read This First; Important Notes; How to Use Error Messages:; Use the error; How to Diagnose Multiple FRUs:; When the; What to Do First:; The servicer must include the

Read This First Before you go to the checkout guide, be sure to read thissection. Important Notes Only certified trained personnel shouldservice the computer. Be extremely careful during write operationssuch as copying, saving, or formatting. Drivesin the computer that you are servicing might ha...

Page 11 - General Preparation; Note

General Preparation Note In this manual, Base Model means the SelectaDock Base Model I, SelectaDock means the SelectaDock II, and SelectaDock Docking System means the Base Model and SelectaDock when docked together as oneunit. 1. The SelectaDock supports the ThinkPad 760E, 760ED, and 760ELD. When an...

Page 12 - Checkout Guide; Obtain the failing symptoms in as much detail as; Use the following table with the verified symptom to; Go to

Checkout Guide Use the following procedure as a guide for computerproblems. Note The diagnostic tests are intended to test only IBMproducts. Non-IBM products, prototype cards, ormodified options can give false errors and invalidsystem responses. Important When the problem determination procedure in ...

Page 14 - Power Supply

Power Supply If the power-on indicator is not on but the power supply fanis not turning, check the power cord for continuity andcorrect installation. If the power cord is not the problem, either the powersupply is defective, or another component is defectivecausing the power supply to cut off. To ve...

Page 16 - Power Supply Connector; Checking the Installed Devices List; Replace the first device in the configuration, such as

Power Supply Connector .5/ 1 19 20 2 Pin Signal V dcMin. V dcMax. 2, 3 GND — — 4 SUB 12 + 11.4 + 12.6 5 GND — — 6, 7 + 12 volts + 11.4 + 12.6 8 GND — — 9—11 + 3.3 + 3.0 + 3.6 12—14 GND — — 15—17 + 5 + 4.75 + 5.25 18—20 GND — — Checking the Installed Devices List If a device is installed but the icon...

Page 17 - Printer; Make sure the printer is correctly connected and is; External Display; Main card of SelectaDock Docking System

System (except the SCSI hard disk). The FDD-2 orPCMCIA-2 icons represent the FDD or PCMCIA attachedthrough a port replicator or in the SelectaDock DockingSystem. Printer Test the printer by connecting it to the computer beforetesting it on the SelectaDock Docking System. 1. Make sure the printer is ...

Page 19 - External Keyboard; Notes; How to Run the Diagnostics

External Keyboard Notes If a mouse or other pointing device is attached,remove it and see if the error symptom goesaway. If the symptom goes away, the mouse orother pointing device is defective. The computer keyboard does not work when anexternal keyboard is connected. 1. Power-off the computer....

Page 20 - How to Run the Keyboard Test:

3. Select a device and press Enter to run the test.4. The test progress screen appears.5. OK appears when the test ends without any errors.6. Start the Advanced Diagnostic test by pressing Ctrl + A on the basic diagnostic menu screen. 7. Select Tool to install the tools.8. Select a device and press ...

Page 22 - Testing the Expansion Unit; The Test Selection Menu appears when you select; Select an item on the screen and follow the; Testing the SCSI Subsystem

Testing the Expansion Unit 1. The Test Selection Menu appears when you select Test Expansion Unit on the Main Menu. 2. Select an item on the screen and follow the instructions that appear on the screen. Testing the SCSI Subsystem Note If a SCSI adapter is installed in an PCI adapter cardslot, remove...

Page 23 - If the initialization fails, the following screen appears:; The SCSI Devices Test Menu appears. Select one; The device name may be any of the following:

2. If the initialization fails, the following screen appears: SCSI Subsystem Diagnostics Utility V2.1 Enter F3=Exit SCSI Initialization Failed If the initialization ends successfully, the followingscreen appears. Select an item. 3. The SCSI Devices Test Menu appears. Select one of the devices. The d...

Page 27 - Numeric Error Codes

Numeric Error Codes Symptom or Error FRUs of the SelectaDockSequence of Actions 10X, 11X 101: Interrupt failure. 102: Timer failure. 103: Timer interruptfailure. 104: Protected modefailure. 105: Last 8042command notaccepted.107: NMI test failure.108: Timer bus testfailure. 109: Low meg-chipselect te...

Page 29 - Diagnostic Error Codes; A detected error is shown as in the following example:; A large X to the left of the device icon; If an error is detected by the diagnostic

Diagnostic Error Codes A detected error is shown as in the following example: A large X to the left of the device icon Device ID (three digit) FRU code (four digit) Error code (two digit) The device ID and error code are used to indicate thedetail portion of the FRU which caused the error. I...

Page 31 - two leftmost digits first then replace the; FRU that is indicated by the; two rightmost digits. No

FRU Codes: If an error is detected by the diagnostic tests, a four-digit FRU code is displayed. The FRU codeindicates two suspected FRUs. Replace the FRU that isindicated by the two leftmost digits first; then replace the FRU that is indicated by the two rightmost digits. No FRU is assigned to code ...

Page 32 - Beep Symptoms; Keyboard-Related Symptoms; Indicator-Related Symptoms

Beep Symptoms Symptom or Error FRUs of the SelectaDockSequence of Actions Beep sounds continuously. 1. Verify that the ThinkPad model iscorrect. (See “GeneralPreparation” onpage 3.) 2. Security feature group 3. Main card 4. Audio card Keyboard-Related Symptoms Symptom or Error FRUs of the SelectaDoc...

Page 33 - Power-Related Symptoms

Power-Related Symptoms Symptom or Error FRUs of the SelectaDockSequence of Actions Although the computer ispowered off, the fan of theSelectaDock power supplyis running. 1. Power supply unit The power of SelectaDockcannot be powered off. 1. Power supply unit Peripheral-Device-Related Symptoms Sympto...

Page 34 - SCSI Device-Related Symptoms

PC-Card-Related Symptoms Symptom or Error FRUs of the SelectaDockSequence of Actions PC Card does not work. 1. Reseat the PC card. 2. Check that: a. The PC card is functional wheninstalled in thecomputer oranotherSelectaDock. b. The PC card is correctly set up,including thecomputerresourceassignment...

Page 35 - Audio-Related Symptoms; Sound Blaster-Related Symptoms

Audio-Related Symptoms Symptom or Error FRUs of the SelectaDockSequence of Actions Audio equipment does notwork. Verify that: 1. The audio equipment works when connecteddirectly to thecomputer. 2. The audio equipment is designed to besupported by thisproduct. Sound Blaster-Related Symptoms Symptom o...

Page 36 - Adapter-Related Symptoms

Adapter-Related Symptoms Symptom or Error FRUs of the SelectaDockSequence of Actions The adapter does not work. Verify that: 1. The adapter is designed for thedocking station adapterslot. 2. The system resources are assigned correctlyby its utility program, ifthe adapter card is anon-PnP ISA adapter...

Page 37 - Intermittent Symptoms; Other Symptoms

Intermittent Symptoms Symptom or Error FRUs of the SelectaDockSequence of Actions An intermittent problemoccurs. The problem can be difficultto analyze because itoccurs intermittently. If yourdocking station has such aproblem, verify that: 1. The computer is firmly attached to the dockingstation. 2....

Page 38 - Undetermined Problems

Undetermined Problems Use the following procedure when the diagnostic tests donot identify the failing adapter or device. Check that all cables, wires, and connectors are connectedso that they do not cause a short circuit. If any problemsare found, reconnect or replace them. Check the power supply f...

Page 39 - Feature Description; This switch controls the MIDI/joystick; Status Indicator; Check the SelectaDock Docking

Feature Description Game Switch: This switch controls the MIDI/joystick port. The Sound Blaster cannot be used when theMIDI/joystick is enabled because of data conflict. Set thegame switch to the OFF position to disable theMIDI/joystick port. Set the game switch to the ON positionto enable the MIDI/...

Page 41 - Removal and Replacement; Caution

Removal and Replacement This section contains information on removals andreplacements, as well as locations. The arrows in the removals and replacements showthe direction of movement to remove a fieldreplaceable unit (FRU), or to turn a screw to releasethe FRU. The arrows are marked in numeric ord...

Page 43 - 020 Option Card Cover / Option Card; If an option card is installed, remove it.

1020 Option Card Cover / Option Card 1 If an option card is installed, remove it. 2 3 35

Page 45 - Attention; UltraBay Tray

1040 1-Inch-High Bay Base Model (1010) The customer can install the ThinkPad option by using theUltraBay tray and HDD, FDD, or CD-ROM by using thedevice tray in the 1-inch-high bay. Remove the devices that are installed in the bay; thenremove the UltraBay tray or device tray as follows: Attention ...

Page 46 - Device Tray

Page 47 - 050 Half-Height Bay Frame

1050 Half-Height Bay Frame Base Model (1010) 1 2 3 39

Page 56 - In step

1130 Audio Card / Main Card / RiserCard Base Model (1010) Rear Panel / Option Card Cover (1020) 1-Inch-High Bay (1040) Half-Height Bay Frame (1050) Upper Cover (1060) Bracket (1070) Cables (1100) Shield Cover (1100) Main Card Assembly (1120) .1/ : To remove the Audio card .2/ : To ...

Page 57 - Locations; Front View

Locations Front View .1/ Multiuser lock .2/ PC Card lock .3/ SelectaDock base lock .4/ Docking guide .5/ Half-height bay .6/ Status indicators .7/ UltraBay tray eject hole .8/ 1-inch-high bay .9/ UltraBay tray .1ð/ FDD connector .11/ HDD connector .12/ UltraBay tray lock .13/ MicroSaver lock hole .1...

Page 59 - Side View; Volume knob

Side View .1/ Volume knob .2/ Headphone jack .3/ Line-out jack .4/ Speaker-in jack .5/ MIDI/joystick port .6/ PCMCIA slots .7/ SCSI connector 51

Page 60 - Rear View; Power jack

Rear View .1/ Power jack .2/ PCI connector .3/ ISA connector 52 IBM Mobile Systems HMM

Page 61 - Parts List

Page 62 - Options

1 Connector cover 73H7450 2 Rear cover 39H7441 3 Bezel (See Upper cover group) 4 Half-height bay frame 82H6729 5 Cable group 73H7453 6 Riser card 39H7442 7 Main card assembly 39H7443 8 Audio card 39H7444 9 Base cover 39H7439 10 Speaker assembly 39H7446 11 Shield cover (See Main card assembly) 12 Pow...

Page 63 - Use the power cord certified for your country.

Power Cords 1 2 3 4 5 6 7 8 9 1 0 Warning Use the power cord certified for your country. 1 Colombia, U.S., Venezuela 13F9959 Japan, 2-pin 6454377 Japan, 3-pin 65F0031 2 Hong Kong, Singapore, U.K. 14F0033 3 France, Germany, Spain 13F9979 4 Italy 14F0069 5 Australia, New Zealand 13F9940 6 Denmark 13F9...