IBM 9516-BXX - Manuals

iv • De fluorescerende lamp in het LCD-samenstel bevat een kleine hoeveelheid kwik (minder dan 50 mg). In verband met milieueisen mag dit product niet als normaal afval gestort worden. Men dient het te verwijderen volgens ter plaatse geldende regels en verordeningen. • Doordat het LCD-samenstel van ...

v • La pantalla de cristal líquido (LCD) es de cristal y puede romperse como resultado de un trato brusco o de una caída. Podría suceder que una pequeña cantidad del material de cristal líquido quedase al descubierto. Este material es irritante; evite tocarlo. Asegúrese de evitar el contacto de sus ...

vi PERIGO Para evitar o perigo de choques eléctricos: • O produto é fornecido com uma ficha com massa e um cabo eléctrico que deverá ser utilizado para ligar à alimentação CA. • O cabo eléctrico deve ser apenas utilizado com uma tomada devidamente electrificada e ligada à massa. • Qualquer equipamen...

vii • Netledningen må kun bruges i en korrekt jordet og tilsluttet stikkontakt. • Alt udstyr, som dette produkt tilsluttes til, skal også være tilsluttet en korrekt jordforbundet og tilsluttet stikkontakt. • Dækslerne må ikke fjernes. • Produktet har ingen strømafbryder. Hvis skærmen skal isoleres f...

viii Håndtering: • Vær forsiktig når du flytter produktet. • Panelet bør ikke brukes i vannrett stilling. • Lysstoffrøret som er brukt i LCD-enheten, inneholder en liten mengde kvikksølv (mindre enn 50 gram). Av miljøhensyn må dette produktet ikke kastes i naturen, men må behandles som spesialavfall...

ix material eftersom det kan orsaka irritation. Om materialet skulle komma i kontakt med ögon, händer m m ska området spolas med vatten i minst 15 minuter; uppsök läkare om du har symptom efter spolningen. VAROITUS Sähköiskuvaaran välttäminen: • Tuotteen mukana toimitetaan maadoitettu pistoke ja lii...

xi TEHLÝKE Elektrik çarpmasý tehlikesinden kaçýnmak için: • Cihaz, elektrik baðlantýsý için topraklanmýþ fiþli bir elektrik kablosuyla birlikte gönderilmiþtir. • Elektrik kablosunun fiþi, elektrik ve toprak baðlantýlarý usulüne uygun olarak yapýlmýþ bir prize takýlmalýdýr. • Bu cihazýn baðlanacaðý d...

3 ENGLISH Setup Hardware Requirements This Monitor requires a computer with a suitable on-board sub-system or Video Adapter card that can support SXGA 1280 x 1024 at 75 Hz. Workplace Preparation Positioning the Monitor This section gives advice on what you should consider before you set up your moni...

4 Working Practices Rest Take regular breaks. Vary your posture, stand up and stretch occasionally as prolonged use of computer workstations can be tiring. This section gives advice on how you can work comfortably and reduce fatigue. Back You should sit back in your chair and use the backrest. Hands...

5 ENGLISH Connecting your Monitor Be sure to read the ‘Safety Information’ at the front of this User Guide before carrying out this procedure. 1. With the monitor standing vertically and at it’s greatest height, remove the cable cover at the rear of the monitor. 2. Turn off your PC and all attached ...

7 ENGLISH Switching on the Monitor Switch on the power source and PC. To turn on the monitor, push and release the power switch. To switch it off, push and release the power switch again. Adjusting the Monitor Position Viewing Angle You can tilt the screen backward or rotate the monitor to the left ...

8 Configuring your Monitor Automatic Setup The Setup Utility included on the setup option diskettes are for displaying color-bar patterns. They do not replace or modify the display driver. When you first use your monitor you must perform Automatic (auto) Setup. This procedure sets up your monitor to...

9 ENGLISH Monitor Information Diskette for Windows 95 To utilise the Plug and Play feature in Windows 95, files should be loaded from the IBM Color LCD Monitor Installation diskette as follows : 1. Turn off the computer and all attached devices. 2. Ensure that the IBM monitor that you wish to instal...

10 Auto Setup for the PC Check the operating system installed on your PC and follow the instructions from the table below. Before carrying out this section it is very important that The Monitor Information Diskette for Windows 95 and Windows 98 has been run. (See page 9). If your PC does not run wit...

11 ENGLISH Auto Setup for DOS 1. Turn on the monitor first; then the PC. If the message UNSUPPORTED VIDEO is displayed, or if nothing is displayed check: • that the video interface cable is connected properly. • the correct video adapter card is installed (see Video Adapters on page 40). • the corre...

14 Auto Setup for the RS/6000 If you are running AIXwindows on the RS/6000, go to Auto Setup for AIXwindows on page 15. Otherwise, check the following table for the type of Video Adapter used with the RS/6000: Video Adapter Type Section GXT150P (RS/6000 Model 43P) Auto Setup for AIXwindows on page 1...

15 ENGLISH Auto Setup for AIXwindows 1. Turn on the monitor, then the RS/6000. The screen remains blue until the system is ready. If the message UNSUPPORTED VIDEO is displayed, or if nothing is displayed check: • that the video interface cable is connected properly. • the correct video adapter card ...

16 Auto Setup for the Gt3i, GXT150, or GXT150L Adapter 1. Turn on the monitor, then the RS/6000. The screen remains blue until the system is ready. If the message UNSUPPORTED VIDEO is displayed, or if nothing is displayed check: • that the video interface cable is connected properly. • the correct v...

18 Auto Setup for the GXT150M Adapter For AIX 3.2 Version 3.2.5.1 and Later 1. Turn on the monitor, then the RS/6000. The screen remains blue until the system is ready. If the message UNSUPPORTED VIDEO is displayed, or if nothing is displayed check: • that the video interface cable is connected prop...

21 ENGLISH 11. Press one of the contrast control buttons. The messages are automatically displayed in the following sequence : ‘OFF-READY- START-COMPLETED’ and auto setup is complete. If “AUTO SETUP COMPLETED” is not displayed, repeat the auto setup procedure several times. If auto setup continues t...

24 Auto Setup for the Sun Workstation If you use OpenWindows with the screen resolution 1280 × 1024, perform auto setup as follows. Otherwise, perform Quick Setup on page 29 1. Set the screen resolution to 1280×1024. Refer to your Sun workstation manuals, Open Windows manuals, or online help to set ...

26 Auto Setup for the HP Workstation 1. Turn on the power of the monitor, then the workstation. If the message UNSUPPORTED VIDEO is displayed, or if nothing is displayed • check that the video interface cable is connected properly. • The screen resolution and the vertical frequency of the HP Sun wor...

28 Manual Setup Normally, you can complete the setup procedure using auto setup. However, if your screen image is still distorted after you perform auto setup, perform manual setup. 1. Wait for about 15 minutes, until the monitor warms up. 2. Display the image you most frequently use on the screen. ...

29 ENGLISH Quick Setup This procedure does not display a color-bar pattern before the setup main menu. To obtain better image quality, you should perform auto setup according to the procedures on the preceding pages with the setup option diskettes for PC-DOS, Window 3.1, Windows 95, Windows NT, OS/2...

30 User controls Front of screen controls The front of screen user controls allow the user to turn the monitor on and off, adjust the brightness and contrast of the monitor to meet the users preferences, and also to gain access to intermediate and advanced On-Screen Display Controls. Icon Control De...

31 ENGLISH On-screen display (OSD) controls To display the OSD, press the setup switch on the back of the monitor as shown. There are eight menus within the OSD. These menus contain the following functions which can be divided into four levels of adjustment : basic, intermediate, advanced and specia...

34 Information Function Location Description H-FREQUENCY Menu 8 of 8 The frequency of the video signal (horizontal sync signal) from your PC (KHz). V-FREQUENCY Menu 8 of 8 The frequency of the video signal (vertical sync signal, or refresh rate) from your PC (Hz). SYNC POLARITY Menu 8 of 8 The polar...

35 ENGLISH Troubleshooting If you suspect something is not working correctly, you should : 1. Turn on the computer and monitor. 2. Set the brightness control to the proper position. 3. Ensure that all cables are securely connected. 4. Disable standby mode if it is enabled. Push the setup switch on t...

36 Further Help If you are unable to correct the problem yourself, you may seek further help as follows: Call the IBM HELPCENTER. In the US call 1-800-772-2227 In Canada call 1-800-565-3344 In other countries contact your dealer, retailer, or other IBM authorized Servicer. Before calling, please hav...

37 ENGLISH Specifications Some types of composite sync signals are not supported. Sync Signal Type The following Sync signal types are supported : • Separate sync (TTL level). • Sync on green *. • Composite sync (TTL level). * Horizontal sync pulses must not be suppressed during the vertical sync pe...

38 Supported Screen Addressability The following table shows the supported screen resolutions : The input signal to this monitor should correspond with the screen resolutions, Hsync frequencies and Vsync frequencies shown in the table. Type Screen Resolution (H × V) Hsync (KHz) Vsync (Hz) VGA 640 × ...

39 ENGLISH Default Preset Timing The monitor retains the following timing parameters for ‘Clock’, ‘Hsync’, ‘Vsync’ and “Total Dots’ as default values. The monitor automatically selects the corresponding values to the video signal from your PC. The Hsync and Vsync frequencies in this table are not th...

41 ENGLISH PC Video Adapters The following are examples of Video Adapters for PCs : • #9 FX Motion 771 Video Adapter (Number Nine Visual Tec. Co.) • #9 Imagine 128 Pro Series 1 (Number Nine Visual Tec. Co.) • ATI 3D EXPRESSION • MGA Millenium 4 MB VRAM (Matrox Graphics Inc.) • MGA Mystique (Matrox G...

42 Video Cables For PC and Sun workstations: For RS/6000: System Part Number Connector to System Unit Connector to 9516 Monitor PC 58F2901 15 pin D-Sub 5 x BNC Sun workstation Video cable for Sun For Sun 5 x BNC or 4 x BNC Graphic Adapter Part Number Feature Number Connector to System Connector to 9...

I COMPL & W A RR &RPSOLDQFHV Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful int...

II For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding type attachment plug rated 13 amperes (minimum), 250 volts. The cord set should be marked <HAR> and have the appropriate safety approvals for the country in which the equipment will be install...

III COMPL & W A RR Industry Canada Compliance Statement This Class A digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Europea...

IV :DUUDQW\ USA., Canada and Puerto Rico Statement of Limited Warranty The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you originally purchase for your use and not for resale, from IBM or an IBM authorized reseller. The term “Machine” means an IBM machine,...

V COMPL & W A RR The service may be 1) a “Repair” service at your location (called “On-Site”) or at one of IBM’s or a reseller’s service locations (called “Carry-in”) or 2) an “Exchange” service, either On-site or Carry-in. If in doubt, contact your point of sale. When a type of service involves...