IBM 2169 - Manuals

3 Notices References in this publication to IBM products, programs, orservices do not imply that IBM intends to make these availablein all countries in which IBM operates. Any reference to an IBMproduct, program, or service is not intended to state or implythat only IBM’s product, program, or servic...

5 To Connect 1. Turn Everything OFF. 2. First, attach all cables to devices. 3. Attach signal cables to receptacles. 4. Attach power cord(s) to outlet. 5. Turn device ON To Disconnect 1. Turn Everything OFF. 2. First, remove power cord(s) from outlet 3. Remove signal cables from receptacles. 4. Remo...

7 DANGER Some CD-ROM drives contain an embedded Class 3A orClass 3B laser diode. Note the following. Laser radiation when open. Do not stare into the beam,do not view directly with optical instruments, and avoiddirect exposure to the beam. ≥≥ 32 Kg ≥≥ 55Kg (70.5 (121.2 lbs) lbs) Caution:Use safe lif...

8 PERIGOPara evitar choques elétricos, não conecte oudesconecte nenhum cabo, nem efetue instalação,manutenção ou reconfiguração deste produto duranteuma tempestade com raios. Para evitar choques elétricos: q O cabo de alimentação deve ser conectado a umreceptáculo corretamente instalado e aterrado. ...

11 PERIGO Algumas unidades de CD-ROM contém um diodo delaser da Classe 3A ou da Classe 3B. Observe oseguinte. Radiação de laser quando aberto. Não olhe diretamentepara o feixe de laser, não olhe diretamente cominstrumentos óticos, e evite exposição direta ao raio. ≥≥ 32 Kg ≥≥ 55Kg (70,5 (121,2 lbs) ...

18 attention:Remplacez la pile usagée par une pile de référenceidentique exclusivement - voir la référence IBM - ou par unepile équivalente recommandée par le fabricant. Si votresystème est doté d'un module contenant une pile aulithium, vous devez le remplacer uniquement par unmodule identique, prod...

20 Le courant électrique circulant dans les câbles decommunication et les cordons téléphoniques etd'alimentation peut être dangereux. Pour votre sécurité etcelle de l'équipement, avant de retirer les carters, mettezcelui-ci hors tension et déconnectez ses cordonsd'alimentation, ainsi que les câbles ...

21 Kabel anschließen 1. Alle Geräte ausschalten und Netzstecker ziehen. 2. Zuerst alle Kabel an Einheiten anschließen. 3. Signalkabel an Anschlußbuchsenanschließen. 4. Netzstecker an Steckdose anschließen. 5. Gerät einschalten. Kabel lösen 1. Alle Geräte ausschalten. 2. Zuerst Netzstecker von Steckd...

24 PERICOLOPer evitare il pericolo di scosse elettriche durante itemporali, non collegare o scollegare cavi, non effettuarel'installazione, la manutenzione o la riconfigurazione diquesto prodotto. Per evitare il pericolo di scosse elettriche: q collegare il cavo di alimentazione ad una presaelettric...

31 caution:Al cambiar la batería, utilice únicamente la batería IBMNúmero de pieza 33F8354 o un tipo de batería equivalenterecomendado por el fabricante. Si el sistema tiene unmódulo que contiene una batería de litio, sustitúyaloúnicamente por el mismo tipo de módulo del mismofabricante. La batería ...

33 Laser Compliance Statement The CD/DVD-ROM drive in the computer is a laser product. TheCD/DVD-ROM drive's classification label (sample shown below)is located on the drive. CLASS 1 LASER PRODUCT APPAREIL A LASER CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 The CD/DVD-ROM d...

34 Trademarks The following are trademarks of the IBM Corporation inthe United States or other countries or both: Operating System/2 OS/2 AT Personal System/2 HelpCenter PS/1 IBM PS/2 Intel, Pentium, MMX, EtherExpress, and LANDesk aretrademarks or registered trademarks of IntelCorporation.Microsoft,...

35 Preface This manual contains service information for the Service Level A (SL-A) model of the IBM Personal Computer, European market only. This manual is intended to be used as a stand-alone documentto service Machine type 2169 product. It is divided into thefollowing chapters: Notices contains im...

36 General Information General Information .......................................................... 36 Introduction .......................................................................... 37Product Overview................................................................. 37Hardware Interfaces ....

38 • Mouse port (6-pin PS/2 mini-din connector) • Two USB ports • Microphone-in jack • Line-out jack • Line-in jack Diskette Drive • AT-type • 3.5-in. 1.44MB • Hard Disk Drive 3.5-in., 1-in. height IDE AT drive. • 512 KB cache buffer in hard disk drive. CD-ROM Drive • 5.25-in. high-performance, 40X ...

39 − Windows 98 power utility timer elapses − System sleep timer elapses Power Supply • 150-watt switchable high/low voltage power supply. • Standard SFX power supply with +5V and +3.3V standbypower Internal Cabling • 40-pin ribbon cable for CD-ROM and ATA-66 cable for harddisk drive. • One 34-pin r...

41 Table 1-1 System Board Hardware Interfaces Item Interface USB USB controller integrated in core logicchip set.

42 Flash (BIOS) Update Procedure NOTE: This system does not deny acces tot he BIOS SetupUtility. The flash update procedure does not change themodel number and serial number information in BIOS. 1. Prepare a bootable DOS diskette with AWD753.EXE and VXXYYZZ.BIN files NOTE: The AWD753.EXE is flash ut...

44 BIOS Setup Utility The Setup Utility lets you review and change importantinformation about the computer and its hardware. Working with the Setup Menus Starting the Setup Utility Follow these steps to enter Setup when the computer is off: 1. Turn on your monitor. 2. Turn on the system unit. 3. Whe...

46 Standard CMOS Features Option This option displays a table of items which defines basicinformation about your system. Date and Time The Date and Time items show the current date and time heldby your computer. If you are running a Windows OS, theseitems are automatically updated whenever you make ...

49 acceleration begins. Typematic Rate (Chars/Sec) Default: 6 If the item Typematic Rate Setting is enabled, you can use thisitem to define how many characters per second are generatedby a held-down key. Security Option Default: Setup If you have installed password protection, this item defines if t...

50 Advanced Chipset Features Option This option displays a table of items that define critical timingparameters of the System Board components including thememory, and the system logic. Generally, you should leave theitems on this page at their default values unless you are veryfamiliar with the tec...

51 Integrated Peripherals Option This option displays a list of items that defines the operation ofsome peripheral components on the system’s input/outputports. IDE device driver controllers can support up to two separatedrives. These drives have a master/slave relationship which isdetermined by the...

53 This item lets you disable the built-in parallel port, or enable itby assigning an I/O address and an Interrupt Request Line(IRQ). Parallel Port Mode Default: ECP ECP Mode Use DMA Default: 3 This item defines the operation of the parallel port. If you areconnected to a parallel device that suppor...

54 Power Management Setup Option This option displays items that let you control the system powermanagement. Operating systems take care of much of thepower management. This mainboard supports ACPI (advancedconfiguration and power interface). The system has variouspower saving modes including poweri...

56 CPU Thermal Limit Default: NA Board Thermal Limit Default: NA These two items can be used to set threshold temperatures forthe CPU and the mainboard. If the temperatures are exceeded,the system uses power management to reduce thetemperatures. CPU Thermal-Throttling Default: 50.0% This item sets t...

58 PNP/PCI Configuration Option This option displays a table of items that configures how PNP(Plug and Play) and PCI expansion cards operate in yoursystem. Reset Configuration Data Default: Disabled If you enable this item and restart the system, any PNPconfiguration data stored in the BIOS setup is...

59 PCI Health Status Option On mainboards which support hardware monitoring, this itemlets you monitor the parameters for critical voltages, criticaltemperatures, and fan speeds. If this option is active on your system, we recommend that youaccept the default values. Frequency Control Option This it...

62 Erasing a lost or forgotten password (clearing CMOS) To erase a forgotten password, or clear a corrupted CMOS: 1. Turn off the computer and all attached devices.2. Unplug the power cord.3. Remove the cover. See “Removing the cover” on page 114. 4. Refer to the system board diagram on page 124 to ...

63 Specifications Dimensions (width x depth x height): • System unit: For machine type 2169: − 380 (h) x 196 9w) x 360 (d) Weight: • System unit: For machine type 2169: − 7.6Kg Environment: • Temperature for system unit: − Power on: 10 ° to 35 ° C − Power off: 10 ° to 43 ° C • Humidity for system un...

64 Operating Requirements All machines require two power inputs: one on the system unitand one on the monitor display. The system unit comes with a voltage selector switch, allowingselection of either 115 V ac or 230 V ac. This switch must be inthe 115V ac position when the machine is plugged into a...

65 Special Tools The following special tool is required to service this systemwhen running the diagnostics program (PC-Doctor): • Wrap plug, P/N 72X854

66 CheckProcedures Check Procedures ............................................................. 66 Introduction .......................................................................... 67Start ...................................................................................... 68Index of Sympt...

67 Introduction This chapter contains the check procedures used to diagnosethe causes of product failures. The diagnostic informationconsists of: Start: This is the starting point for any diagnostic action. Based on high-level symptoms, the check procedure directs youto more detailed procedures to h...

68 Start This is the entry point for all check procedures. The checkprocedures use failure symptoms, Power-On Self Test (POST)error codes, or beeps to help determine the defective fieldreplaceable unit (FRU). Follow the suggested check proceduresor use the diagnostics diskette to determine the probl...

72 005 - q If the keyboard responds incorrectly, go to "Keyboard" on page 96. 006 - DOES THE SYSTEM CONFIGURATION REPORTCORRECTLY IDENTIFY THE DEVICES INSTALLEDIN SYSTEM? (YES, READ AHEAD. NO, GO TO STEP007.) q Select Diagnostics from the diagnostics program menu. q Select and execute All Te...

73 008 - DOES THE DIAGNOSTICS FINISH WITHOUT ANYERRORS? (YES, READ AHEAD. NO, GO TO STEP009.) q If the Diagnostics \ All Tests did not detect a failure but the system still indicates a failure: q Check all adapter card jumper settings. q Check all adapter cards switch settings. q Check all adapter c...

74 Index of Symptoms, Messages, Error Codes, or Beeps How to Use Error Messages: Use the messages, error codes, and beeps combinations that occur to diagnose failures. If morethan one failure occurs, diagnose from the first failure thatappears. The cause of the first failure can result in falsemessa...

75 NOTES: If an error message and incorrect audio response occur,diagnose the error message first. If you cannot run the diagnostics program tests but did receivea POST error code, diagnose the POST error message. If you did not receive any error message, look for a descriptionof your error symptoms...

78 Table 2-2 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes,Messages, beeps Action/FRU NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to acheck procedure, replace the FRU indicated in the checkprocedure. If no check procedure...

82 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace theFRU indicated in the check procedure. If no check procedureis indicated, the first Action/FRU listed in right column i...

87 Troubleshooting Failing Parts or Assemblies: The check procedures generally help you trace a problem to one part or assembly. The last stepof the specific check procedure you are using indicates that apart or assembly is failing. You should inspect the part orassembly before you decide to replace...

93 Audio (Not Supported by Diagnostics Program) NOTE: Audio tests for the sound card cannot be carried outin the PC Doctor DOS diagnostics program. It is,however, possible to carry out a dial tone test for themodem. While performing this check, you may need to enterand exit Microsoft Windows 98 seve...

100 1 11 10 20 Power Supply Connectors (Bottom View) Hard Drive or CD-ROM End of Power Cable 3.5-In. Diskette Drive End of Power Cable

104 Undetermined Problems If an error code is present, go to “Index of Symptoms,Messages, Error Codes, or Beeps” on page 74. If no error codeis present, continue with this check. Check the power supplyvoltages (see “Power Supply Cable Connector Specifications"on page 129). If the voltages are co...

105 Diagnostic Aids Diagnostic Aids.................................................................. 105 Introduction .......................................................................... 106Power-On Self Test ............................................................. 106Diagnostics Tools ....

107 4. If no keyboard keys are pressed, and if POST is completed without errors, the system will then proceed with the loadingof DOS or other operating system from diskette drive A or ahard disk drive or CD-ROM drive, depending on the optionsselected in the Setup Utility. If any errors are detected ...

110 Repair Information Repairing Information ....................................................... 110 Removals and Replacements of machine type ................. 111Identifying the Parts of the System Unit.............................. 112Top Cover ...................................................

111 Removals and Replacements of machine type 2169 BEFORE REMOVING ANY FRU, POWER-OFF THECOMPUTER UNPLUG ALL POWER CORDS FROMELECTRICAL OUTLETS, THEN DISCONNECT ANYINTERCONNECTING CABLES. ATTENTION: The System board, processors, adapter cards, DIMMs, and upgrade processors can be damaged byelectrost...

112 Identifying the Parts of the System Unit This computer system has 4 bays, each bay may have afactory-installed drive in it. The devices are 3.5” Diskette, 40XCD-ROM drive (some models only) and 5.0 GB hard disk (somemodels may have hard disk of 7.5 or 10 GB capacity). Diskette drives in this uni...

114 Top Cover To remove the top cover of this system unit: q Remove the 3 screws that secure the top cover at the back of the system unit. q Hold both sides of the system unit cover and push it backward about 25 mm. q Lift the top cover up to remove it completely. q Touch the bare metal frame of you...

115 Adapter Cards Installing Adapter Cards q Remove the screw that secures the adapter card retainer and slot cover. Then remove the card retainer and slotcover. q Align and insert the adapter card into the adapter card connector. q Secure the card with the screw that you removed in the first step. ...

116 Removing Adapter Cards Follow these steps to remove an adapter card: q Position the system unit so that the card is accessible to you. q If the adapter card has cables, disconnect them. Be sure to take note of where the cable is connected. You will haveto reconnect these cables when you reinstal...

119 Hard Disk Drive To remove or replace the hard disk drive: q Disconnect the power and signal cables from the back of the diskette and HDD drives. q Remove the single screw on the side of the cage q Remove the diskette mounting tray from the chassis as following illustration : Slide the drive-moun...

120 System Board To remove the system board from the system: q To remove the system board. You must remove the adapter cards first. q Disconnect the power cable, CD-ROM cable, Diskette Drive cable, Hard Disk Drive cable, audio cable, powerswitch cable and LED cables from system board. q Remove the t...

121 Power Supply This system has a 150-watt switching power supply. 1. To remove the power supply. You must remove the top cover first. 2. Disconnect the power cable from the riser board and all drives. 3. Remove the screws in the machine rear that secure the power supply. Memory (DIMM) This system ...

122 Parts/Test Point Locations Parts/Test Point Locations ............................................... 122 Introduction .......................................................................... 123System board LayoutPower Supply Cable Connector Specifications .................. 129 Main Output P...

124 Layout of system board of the machine type 2169 CASFAN1 CPUFAN1 DIMM1 DIMM2 JP2 FDD1 IDE2 IDE1 PANEL1 SIR1 WOM1 WOL1 JP1 J1 FP1 CD2 TV-Out/LCD Panel Riser Slot CD1 Socket-370 PCI1 PCI2 ATX1 COM2 LED1 J2 JP3 USB1 LED2 MODEM2 Component Description Socket-370 Socket for PPGA Celeron Processor PCI 1...

127 PANEL1: PANEL CONNECTORS FOR SWITCHES AND INDICATORS The panel connector is used to implement the switches andindicators on your system case. Note: Only pins 15, 16 (Hard Disk Indicator) and pins 21, 22(Power Switch) are used on 2169 standard models. ConnectorJ2, referred to on the system board ...

128 Replacing the system battery Follow these steps to replace the battery: 1. Place the blade of a small, flat-blade screwdriver under the edge of the retaining clip. 2. Turn the screwdriver one quarter turn, raising the clip while pressing down on the old battery to remove it. 3. Carefully raise t...

129 Power Supply Cable Connector Specifications Refer to the following figures when checking for voltages onpower supply cable connectors. When checking voltages, the power supply fan must be running.To power on the power supply without using the on/off switch,use a screwdriver or other tools to sho...

131 Hard Drive or CD-ROM Power Cable Connector 3.5-In. Diskette Drive Power Cable Connector

132 Factory-Installed Modem Card Layout Factory-Installed Modem Card Layout Factory-Installed Modem Card Connector Functions Item Function Connect to… 1 Telephone line-outSome modem adapters may comewithout this jack. Telephone set 2 Telephone line-in Telephone line NOTE: Care should be taken while ...

134 CD-ROM Drive CD-ROM Front Panel NOTE: Position of CD-ROM switches and LEDs may varyfrom illustration. Item Description 1 Load / eject button 2 Headphone jack 3 Power-on / busy indicator, lights up in green colorwhile disc is set in ready state; lights up andflashes in amber color during data rea...

140 Safety Inspection Guide Safety Inspection Guide ................................................... 140 General Guidelines .............................................................. 141  Copyright IBM Corp. 2000

141 General Guidelines The purpose of this Safety Inspection Guide is to help youidentify possible unsafe conditions on machines that are beinginspected for a Maintenance Agreement. Each machine hasnecessary functions items installed to provide the operators andservice personnel with an acceptable l...

143 Parts Catalog Part Catalog of machine type ............................................. 144Assembly 1: System Unit..................................................... 144 Assembly 2: Diskette Drive, Hard Disk Drive ................ 147 Assembly 3: CD-ROM, Modem Card...............................

144 Part Catalog of machine type 2169 Assembly 1: System Unit Asm-Index FRU Number Description 1 See Assy 3 40x CD-ROM 2 11P7621 Power Supply 150W Asm 3 See Assy 2 Floppy Disk Drive 4 See Assy 2 HDD Drive 5 09N9307 INTEL Celeron 533MHz assywith fansink 6 06P2446 Fansink, Supports Celeron(non-PIII ba...

146 Not Shown 11P7610 ECS Screw Kit (All screwsexcept CD and HDD). Not Shown 11P7610 IBM Screw Kit (for CD + HDD) Not Shown 11P7559 Chassis Feet

147 Assembly 2: Diskette Drive, Hard Disk Drive Asm-Index FRU Number Description 2-1 19K1583 5 GB Hard Disk Drive, 3.5” 2-2 11P7556 3.5”, Diskette Drive 2-3 11P7554 HDD IDE Cable (DMA 66 MHz) 2-4 11P7553 FDD IDE Cable

148 Assembly 3: CD-ROM, Modem Card Asm-Index FRU Number Description 3-1 09N0879 40X CD-ROM, LG 3-1 19K1515 40XCD-ROM, LITEON 3-2 37L5098 CD-ROM IDE Cable 3-3 75H9219 CD-ROM Audio Cable (2169) 3-5 09N1676 Modem, 56K Data Fax, GVC EMEA/ANZ/India/Singapore 3-4 09N1626 Modem, 56K Data Fax,Askey EMEA 3-5...

150 Assembly 4: Keyboard and Mouse 4-2 4-1 4-3 Asm-Index FRU Number Description 4-1 10L6145 IBM Mouse 4-2 37L2518 105 PALM REST ARABIC 275 4-2 37L2519 105 PALM REST, EUROBELGIUM/FR 120 4-2 37L2520 105 PALM REST, EUROBELGIUM/UK 120 4-2 37L2521 105 PALM RESTBULGARIAN 442 4-2 37L2522 105 NO PALM RESTCZ...

152 Appendix A. Online Support Information This section describes online technical support servicesavailable to help repair the computer. This section covers: q IBM PC Company Fax-Back Service q IBM useful sites on the World Wide Web (WWW) q IBM Online Assistant q Discussion Forums The IBM PC Compan...

Printed in U.K International Business Machines Corporation Old Orchard Road, Armonk, New York 10504 Part Number: 11P7604 Date: 7/00