IBM 09N4153 - Manuals

Preface This manual contains instructions for installing and using the IBM 9.4/4.7 GBDVD-RAM Drive with Software MPEG-2 Option Kit. The manual is dividedinto the following parts: Part 1: Installation and user ’s guide This guide contains the product description and installation instructions in thefo...

Installation and user’s guide This section contains the product description, hardware and softwareinstallation instructions, and operating information for the IBM ® 9.4/4.7 GB DVD-RAM Drive. Product description 9.4/4.7 GB DVD-RAM Drive with MPEG-2 Software This option package is intended for multime...

With this MPEG-2 software, you do not need to install an MPEG-2 adapterin your computer to view DVD video files. The software CD contains anMPEG-2 decoder and programs that work with Windows 98, Windows 95OSR2, Windows 2000, Windows NT 4.0, and Windows Me. You can use thesoftware to play high-resolu...

Drive controls and connectors The following diagrams show the location and functions of the drive controlsand connectors. Front view of the drive 1 Disc drawer This drawer is where you load and unload a disc. 2 Headphone jack This jack provides audio output to the headphones. 3 Volume control This d...

Rear view of the drive Pin 1 1 Reserved 2 Audio-out connector This connector transmits the analog audio signals to an audio adapter. 3 Configuration pins These pins are used to set the drive configuration. 4 IDE port This connects the DVD-RAM drive to the IDE cable. 5 Power connector This connects t...

If you must put the drive down, place the antistatic bag on a flat, paddedsurface, such as a magazine, and place the drive on the antistatic bag. Step 3. Setting the configuration jumpers You can configure your drive as master 1 , slave 2 , or cable-select 3 , as shown. Use the following guidelines ...

Step 4. Mounting the drive in the bay Attention: Be sure to use the M3 x 5-mm mounting screws in the option package when you are driving screws directly into the drive. Using screws thatare too long might damage the drive. You can mount the DVD-RAM drive horizontally or vertically in the computer.If...

1. Insert the InstantWrite SoftwareCD in the CD-ROM or DVD-RAM drive ofyour computer. 2. Double-click My Computer. 3. Double-click the icon for your CD-ROM or DVD-RAM drive. 4. Double-click SETUP.EXE. The Install Wizard window opens. 5. Follow the on-screen instructions. 6. When you are prompted, re...

11. Click OK. 12. Click OK again. 13. Click Close. 14. Restart your computer to enable the DMA of your DVD-RAM drive. Step 11. Installing the MPEG-2 Decoding software forWindows 98, Windows 95 OSR2, or Windows Me. Note: Before installing MPEG-2 decodingsoftware, be sure to read “Changingthe DVD regi...

Refer to the documentation that comes with your computer for information onother system-board manufacturers. When you have located the Windows NT 4.0 DMA device driverrecommended by your system board manufacturer, download and extract it toa directory on your hard drive. For more directions, go to “...

protect the media. 2. Reverse the procedure to enable writing on the media again. Using single- and double-sided DVD-RAM media DVD-RAM media is available in single-sided and double-sided versions. 2.6 GB and 4.7 GB versions are single-sided and are available in Type I or TypeII cartridges. 5.2 GB an...

Returning the disc to the cartridge To return the disc to the cartridge, align the label side of disc 1 with the DVD-RAM cartridge label side. Insert the disc and close the cartridge lid 2 . A clicking sound will ensure the lid door is closed. Precautions for handling Be careful when handling the re...

The DVD-RAM drive has two plastic clips near the front of the loading traythat must be lifted up to secure a bare disc for vertical mounting operation. Toraise the clips, open the tray, remove any discs that might be present, and pushthe clips up using the side tabs by pushing from the underside of ...