Hunter 42656-01 - Manuals - manualsarea.com

Page 2 - Welcome; ceiling fan is an addition to your home or office that; Cautions and Warnings; qualified electrician.; Table of Contents

2 42656-01 • 08/14/09 • Hunter Fan Company Welcome Your new Hunter ® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan.We are proud o...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Standard Mounting; Understanding Mounting and Installer’s Choice; of three ways, depending on ceiling height and your preference: Low; Considering Optional Accessories; performance of your Hunter fan, use only Hunter speed controls.

3 42656-01 • 08/14/09 • Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s For ceilings higher than 8 feet, you can purchase Hunter extension downrods. All Hunter fans use sturdy 3/4” diameter pipe to assure stability and wobble-free performance. Standard Mounting hangs from the c...

Page 4 - • Gettin g R eady; To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?

4 42656-01 • 08/14/09 • Hunter Fan Company 1 • Gettin g R eady To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need h...

Page 5 - • Inst al lin g th e C ei lin g Pl at e; To avoid possible electrical shock, before installing your fan,; outermost holes in the outlet box. The pilot holes should be 9/64”; For Angled Ceilings:

5 42656-01 • 08/14/09 • Hunter Fan Company 2 • Inst al lin g th e C ei lin g Pl at e CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit...

Page 6 - • A ssemblin g th e Fan; Fan may fall if not assembled as directed in these; -2. Insert the downrod through the canopy and canopy trim ring.; • Hanging and Wiring the Fan; The adapter has a special coating on the threads. Do; Standard or Angled Mounting

6 42656-01 • 08/14/09 • Hunter Fan Company 3 • A ssemblin g th e Fan Steps 3-2 – 3-3 Downrod Canopy Set Screw WARNING: Fan may fall if not assembled as directed in these installation instructions. 3-1. Unbundle the wires from the fan.For Standard or Angled mounting: 3-2. Insert the downrod through t...

Page 7 - • Han g in g and Wirin g th e Fan; Note: To hang the fan, you must tilt the canopy to an almost vertical; position so that the canopy slots sit on the ceiling plate hooks.; location is still OFF.; Be sure no bare wire or wire strands are visible after; Single Switch Wiring:; If you want to, you can control both fan and light with one switch. To; Dual Switch Wiring:; • The bare or green ground wire from the ceiling to the green; Single Switch Wiring

7 42656-01 • 08/14/09 • Hunter Fan Company 4 • Han g in g and Wirin g th e Fan 4-1. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate ho...

Page 8 - • Inst al lin g th e C anopy and C anopy Trim Rin g; Failure to complete the following steps could cause the fan; -1. Rotate the hanger ball so the tab in the canopy is secure in the; The slots in the canopy must remain engaged while; -3. Holding the canopy up with the screw holes aligned, partially

8 42656-01 • 08/14/09 • Hunter Fan Company 5 • Inst al lin g th e C anopy and C anopy Trim Rin g WARNING: Failure to complete the following steps could cause the fan to fall. Note: It is recommended you use a magnetic tip screwdriver for the following steps. 5-1. Rotate the hanger ball so the tab in...

Page 9 - • A ssemblin g th e Bl ade s; blade screws to attach the medallion to the blade iron. Repeat for

9 42656-01 • 08/14/09 • Hunter Fan Company 6 • A ssemblin g th e Bl ade s Step 6-1 (Detail) Blade Assembly Screws Use with grommet Use without grommet Grommet Step 6-4 Blade Iron Mounting Screw Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan).6-1. Install t...

Page 10 - Both plug connectors are polarized and will only fit together; • Inst al lin g th e Li g ht Fi xture; Note: In compliance with US federal energy regulations, this; ceiling fan contains a device that restricts the light kit to a

10 42656-01 • 08/14/09 • Hunter Fan Company Step 7-1 Housing Assembly Screw Housing 7-1. Partially install two housing assembly screws into the housing.7-2. To attach the light fixture, connect the upper plug connector from the motor to the lower plug connector in the light fixture assembly. Note: B...

Page 11 - cover plate and glass bowl.; • Inst al lin g th e Li g ht Fi xture (c ontinu ed)

11 42656-01 • 08/14/09 • Hunter Fan Company 7-6. Remove the breakaway connectors from the light and fan pull chains and thread them both through the hole in the center of the glass bowl. 7-7. Place the cover plate up against the glass bowl. Align the holes in the cover plate and glass bowl. 7-8. Thr...

Page 12 - • O p eratin g and Cleanin g Your C ei lin g Fan; In warm weather; In cold weather; • The chain uses a breakaway connector that separates if the; To Change Airflow Direction; Turn the fan off and let it come to a complete

12 42656-01 • 08/14/09 • Hunter Fan Company 8 • O p eratin g and Cleanin g Your C ei lin g Fan In warm weather , use downward air flow pattern In cold weather , use upward air flow pattern 8-1. Turn on electrical power to the fan.8-2. The fan pull chain controls power to the fan. The pull chain has ...

Page 13 - • Trouble sho otin g; Problem: Lights dim when turned on or do not turn on; Turn the power to the fan off at the wall switch. Wait 30

13 42656-01 • 08/14/09 • Hunter Fan Company 9 • Trouble sho otin g Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing.4. Pus...