Page 2 - HULK Power; Model Specifications
2 HULK Power Model Specifications ● Model: HI05V08Y1 HS05V08Y1 (with noise suppression) ● Motor: 230 V (+ or - 10%) ~ 60 Hz, Single Phase ● No-load motor speed: 1750 rpm ● Power: 5 HP ● 2 stage, 3 cylinder, cast-iron piston pump ● Max. pressure: 155 psi ● No-load pump speed: 790 rpm ● Pump oil capac...
Page 3 - Stationary Air Compressor; Inspection; Description; Get to know your compressor
3 HI05V08Y1/HS05V08Y1 man v.190811 Stationary Air Compressor Inspection ● Inspect compressor prior to any use. ● Check for external damage that might have occurred during transit. Check for possible damage from transit and test the pulley by turning it freely with your hands. Be careful of moving pa...
Page 4 - Safety Information
4 HULK Power 4 of excessive pressure build up. The safety valve is preset at factory. Do not attempt to make any adjustments to the safety valve. Periodically pull the ring on the safety valve end to check that it is working properly. 5. RESERVOIR AIR PRESSURE GAUGE - Indicates pressure of compresse...
Page 5 - CALIFORNIA PROPOSITION 65; Basic Guidelines; Breathable Air
5 HI05V08Y1/HS05V08Y1 man v.190811 Stationary Air Compressor CALIFORNIA PROPOSITION 65 This product or its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. Basic Guidelines 1. Allow only trained...
Page 6 - Installation; Area; Electrical Safety
6 HULK Power safety glasses. Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid safety shoes, hard hat, or hearing protection should be used in appropriate conditions. 2. Wear proper apparel. Loose clothing, gloves, neckties, rings, bracelets, or other jewelry may present a potential ha...
Page 7 - Operation; Safety Rules; Air Tool Cautions
7 HI05V08Y1/HS05V08Y1 man v.190811 Stationary Air Compressor 13. Always disconnect the tool from power source before making any adjustments, storing, servicing, or changing accessories. Such preventative safety measures reduce the risk of starting the tool accidentally. 14. Keep away from flammables...
Page 8 - Getting Started; Power Requirements; all; Assembly; Before operating your air compressor:
8 HULK Power 2. Make sure all hose connections are adequately secured to prevent tools or hose ends from being accidentally disconnected. 3. Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a moving part of the tool may result in personal injury....
Page 9 - General Overview; Installation and Location; Air Intake
9 HI05V08Y1/HS05V08Y1 man v.190811 Stationary Air Compressor check that all pipes and hoses are firmly connected. ● Do not use the air compressor if any damage is found. If damaged, have an authorized service center inspect and test the air compressor to ensure that is working properly. ● Pull the r...
Page 10 - Starting; Pressure Switch; Maintenance; Service
10 HULK Power Starting ● Check oil level before starting. The oil should be in the center of the sight glass. ● Turn the compressor over a few revolutions by hand to make sure that everything is free. ● Check belt tension. (should be ½’’ of play). ● Remove rags, tools, and any other objects from the...
Page 11 - Daily; Monthly; Troubleshooting; Belt Adjustment; Slow Pumping Or Insufficient Pressure; Await
11 HI05V08Y1/HS05V08Y1 man v.190811 Stationary Air Compressor Daily ● Before each use, 1. check for any unusual noise or vibration.2. be sure all nuts and bolts are tight. ● After each use, drain condensation from the air tank. Weekly ● Inspect air filters (fig.6) weekly and clean or change as neede...
Page 12 - Overheating; Storage
12 HULK Power Overheating Compression of air generates heat, much of which is dissipated as air passes over the intercooler and/or after cooler. Overheating can be caused by: 1. Pump running backwards (reverse direction). Proper rotation is counter-clockwise when facing the flywheel. 2. One or more ...
Page 13 - Troubleshooting Chart; Trouble
13 HI05V08Y1/HS05V08Y1 man v.190811 Stationary Air Compressor Troubleshooting Chart Trouble Possible Cause Corrective Action Compressor will not start 1. Blown fuse or circuit breaker tripped 1. Replace or reset fuse/circuit breaker 2. Loose electrical connections 2. Check wiring connnections Low pr...
Page 14 - Hulk Warranty Statement; SMART OILTM
14 HULK Power Hulk Warranty Statement Hulk Power by EMAX Compressor makes the following Warranty guarantee: ● Standard warranty: That each compressor unit is free from defects in material, workmanship, and parts for 1 year from the date of purchase. Hulk Power by EMAX is not reasonable for downtime ...
