Huffy RC3200 - Manuals - manualsarea.com

Page 2 - MOVING SYSTEM; WARNING

2 P/N 211657B 04/03 Crank Height Indicator Hook 201254 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. Rotate basketball system forward, while holding pole,until wheels engage withground. 3. Move basketball system to desired location. 4. Carefully rotate baske...

Page 3 - LARGE; Wood Scrap; BOTTOM VIEW

3 04/03 P/N 211657B IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL 1. Carefully, position front tank (1) upside down. Secure wheel (2) into place from bottom side (illust. A) making sure the wheel bracket (5) seeds into base as in illust. B. Repeat procedure for opposite...

Page 5 - DO NOT

5 04/03 P/N 211657B Loosen hardware on collar (10) andsecure struts (20) to collar (10) as shownand tighten. NOTE: Final adjustments to collarmay need to be made. Refer to Step32. 10. FRONT VIEW 20 20 11 10 13 20 12 14 12 9. Carefully position system on its side, and securebottom of pole to tank as ...

Page 7 - ELEVATOR INSTALLATION

7 04/03 P/N 211657B MTT01.EPS 27 4 6 24 24 4 6 26 4 4 13. Install left screw jack support plate (26) and right screw jacksupport plate (27) to pole. Finger tighten. ELEVATOR INSTALLATION TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY ...

Page 8 - DO NOT OVER; FRONT VIEW OF; TWO PERSON MINIMUM REQUIRED

8 P/N 211657B 04/03 15. 16. 1 7 9 8 32 Center screw jack (29) between support plates (26 & 27)and secure as shown below. Finger tighten. Place cover over screw jack (29). Install pole cap (32). 28 29 33 26 7 27 4 4 33 IMPORTANT! DO NOT OVER TIGHTEN. 31 14. Attach height decal (28) on screw jack ...

Page 9 - Be sure to use proper bracket as shown.

9 04/03 P/N 211657B 37 NOTE: Be sure to use proper bracket as shown. 17. 36 36 35 35 19 19

Page 12 - NOW COMPLETELY TIGHTEN ALL

12 P/N 211657B 04/03 ½ Secure board and elevator tube assembly to pole assembly as shown. Finger tighten. IMPORTANT! DO NOT OVER TIGHTEN. 4 6 38 38 40 4 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING In...

Page 13 - Add one gallon

13 04/03 P/N 211657B MTT02.EPS211307 Make final adjustments to levelthe rim. If backboard and rim aretipped back, raise collar (10) untillevel and tighten. If backboardand rim are tipped forward, lowercollar until level and tighten.Maximum adjustment travel is 33”to 37” (84-94 cm) from bottom ofpole...

Page 14 - Height Adjustment; HOOK; Regulation Rim

14 P/N 211657B 04/03 Position looped end of height adjustment crank(34) onto hook as shown. Rotate crank handleto raise or lower backboard. View label (28) todetermine approximate backboard height. NOTE: If height adjustment is difficult tooperate, you may have over tightened theareas indicated. Hei...

Page 15 - YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.; HARDWARE IDENTIFIER

15 04/03 P/N 211657B Item #3 (2) Item #6 (13) Item #15 (1) Item #11 (4) Item #4 (24) * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. HARDWARE IDENTIFIER (CONTINUED) Item Qty. Part No. Description 1 1 226350 Tank, (Front Section) 2 2 226403 Wheel 3 2 206245 Bolt, Hex Head, 1/2-13 x 5-1/2 Long 4 24 203474...