Huffy Portable System - Manuals

Page 2 - any excess paint from holes if necessary.

2 P/N 211022 01/05 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular ...

Page 3 - WARNING

01/05 P/N 211022 3 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or ...

Page 4 - NOTICE TO ASSEMBLERS

4 P/N 211022 01/05 For more information on assembly, placement, properuse, and maintenance, visit The American BasketballCouncil website at http://www.smarthoops.com. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. NO...

Page 5 - MOVING SYSTEM; SAFETY INSTRUCTIONS

01/05 P/N 211022 5 LEVER 1 2 BROOM HANDLE 201257 3/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. While holding pole, rotate basketball system forwarduntil wheels engage withground. 3. Move basketball system to desired location. 4. Carefully rotate basketball s...

Page 6 - FRONT

6 P/N 211022 01/05 Get to know the basic parts of your basketball system..... SUPPORT STRUT BACKBOARD FRONT RIM BASE POLE

Page 7 - PARTS LIST - See Hardware Identifier

01/05 P/N 211022 7 * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. WARRANTY CARD: Please remember to complete your productregistration form either on-line at:www.huffysports.com/warrantycard or mail-in the enclosed postcard. WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLICBACKBOARD, EXAMINE BACKBOARD...

Page 10 - SECTION A: ASSEMBLE THE BASE

10 P/N 211022 01/05 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE This is what your system will look likewhen you’ve finished this section: (2) 1/2”, (2) 9/16" AND (2) 3/4" Wrenches 9/16” 1/2” AND/OR (2) Socket Wrenches and Socke...

Page 17 - SECTION B: ATTACH THE BACKBOARD

01/05 P/N 211022 17 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ATTACH THE BACKBOARD This is what your system will look likewhen you’ve finished this section: (2) 1/2”, (2) 9/16"” AND (2) 3/4” Wrenches 9/16” 1/2” 3/4” AND/OR (2) Socket Wrenches and ...

Page 19 - Support pole on sawhorse.

01/05 P/N 211022 19 Support pole on sawhorse. Attach upper and lower elevator tubes (44) to upper pole section (4) using bolts (43) and nuts (39)as shown. Attach pole cap (22) as shown. 3 . 39 44 44 43 43 39 22 4 44 44 TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULTI...

Page 20 - Push second “arm” back and into ram as shown.

20 P/N 211022 01/05 5. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clipslightly so that second “arm” slides over the top of the first “arm”as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “bo...

Page 21 - NET INSTALLATION

01/05 P/N 211022 21 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 6. 21 20 26