Huffy P/N 21147703 - Manuals

Page 2 - WARNING

2 P/N 21147703 03/04 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces o...

Page 3 - NOTICE TO ASSEMBLERS; SAFETY INSTRUCTIONS

03/04 P/N 21147703 3 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water acco...

Page 5 - Item Qty

03/04 P/N 21147703 5 Item Qty Part No. Description 1 1 908026 Top Pole Section 2 1 908107 Middle Pole Section (with Label) 3 1 908015 Bottom Pole Section 4 1 900223 Wheel Bracket 5 1 206940 Axle 6 2 226403 Wheel 7 2 206938 Pushnut 8 1 206660 Base 9 6 203156 Hex Bolt, 5/16-18 x 1 10 18 203218 Flat Wa...

Page 8 - any excess paint from holes if necessary.

8 P/N 21147703 03/04 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular...

Page 9 - SECTION A: ASSEMBLE THE POLES; POLE

03/04 P/N 21147703 9 SECTION A: ASSEMBLE THE POLES WARNING LABEL 2 1 3 I.D. Label I.D. Label 1. Correctly identify each pole section. 2. WOOD SCRAP (NOT SUPPLIED) 2 1 Align dimple of top pole with slot of middle pole. While maintaining alignment, bounce middle pole(2) into top pole section (1) using...

Page 11 - SECTION B: ASSEMBLE THE BASE; a Hammer or

03/04 P/N 21147703 11 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BASE This is what your system will look likewhen you’ve finished this section: a Hammer or Mallet (2) 1/2” AND (2) 9/16" Wrenches AND/OR (2) Socket Wrenches and Sockets A...

Page 15 - SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARD; Wrenches

03/04 P/N 21147703 15 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARD This is what your system will look likewhen you’ve finished this section: 9/16” 1/2” 3/4” (2) 1/2”, (2) 9/16"” AND (2) 3/4” Wrenches AND/OR (2) S...

Page 18 - Face of Backboard

18 P/N 21147703 03/04 Insert handle assembly through pole mount assembly asshown. Lock pole assembly in place at the 10’ (3.05 m)mark with pin (27). 27 5 . 6. 30 30 29 29 31 45 Assemble backboard brackets (45)using spacers (30), bolts (29), andnuts (31) as shown. 31 IMPORTANT!: KEEP HARDWARE LOOSE U...

Page 23 - SECTION D: SECURING THE SYSTEM

03/04 P/N 21147703 23 1. SECTION D: SECURING THE SYSTEM Roll assembly to desired playing area. Secure assembly to ground using rope (56)and tie down stake (36). Fill base (8) with water (approx. 40 gallons) and snap fillcaps (37) in place. 56 36 37 8 37 TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE ...

Page 24 - SECTION E: INSTALL FRONT COVER; STANDOFFS

24 P/N 21147703 03/04 SECTION E: INSTALL FRONT COVER 1. Install front cover (38) by lining up stand-offs along the tank struts. Insert a tie strap(39) through the top two and bottom two stand offs. Wrap tie straps around tankstruts as shown and secure tightly. Trim excess of tie strap as shown in FI...

Page 25 - Push second “arm” back and into ram as shown.; SECTION F: NET INSTALLATION

03/04 P/N 21147703 25 1. Install clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” ofclip slightly so that second “arm” slides over the top of thefirst “arm” as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “body...

Page 26 - Insert net into bottom of clip as shown.

26 P/N 21147703 03/04 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP 2. 40 57 58

Page 27 - SECTION G: APPLY HEIGHT AND MOVING LABEL

03/04 P/N 21147703 27 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. While hol...

Page 28 - SECTION H: HEIGHT ADJUSTMENT

28 P/N 21147703 03/04 SECTION H: HEIGHT ADJUSTMENT 1. A. While holding handle, remove pin (27).B. Move elevator up or down to desired height.C. Replace pin (27) full length to lock system at desired height. 27 A. B. C. 51 DO NOT ALLOW CHILDREN TOADJUST HEIGHT. WARNING!