Huffy M731321 - Manuals - manualsarea.com

Page 2 - WARNING

2 ID# M731321 11/05 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular...

Page 3 - SAFETY INSTRUCTIONS

3 11/05 ID# M731321 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble th...

Page 4 - NOTICE TO ASSEMBLERS

4 ID# M731321 11/05 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections, hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration form eitheron-line at:www.huffysports.com/customer_support/product_registration ...

Page 5 - FRONT VIEW

5 11/05 ID# M731321 FRONT VIEW POLE SUPPORT STRUT BASE Get to know the basic parts of your basketball system... ELEVATOR ADJUSTMENT BACKBOARD RIM

Page 6 - PARTS LIST - See Hardware Identifier

6 ID# M731321 11/05 PARTS LIST - See Hardware Identifier Item Qty. Part No. Description 1 1 206657 Tank, (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel, 4“ (Black) 4 1 90021701 Top Pole Section 5 1 904840 Middle Pole Section 6 1 900136 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 20...

Page 9 - reference point in the next step.; ITEMS REQUIRED FOR THIS SECTION; SECTION A: ASSEMBLE THE BASE; Identification Sticker

9 11/05 ID# M731321 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. ITEMS REQUIRED FOR THIS SECTION 1. 4 5 6 9/16” 1/2” This is what your system willlook like when you’vefinished this section. (2) 1/2” and (2) 9/16&#...

Page 12 - The Warning Label

12 ID# M731321 11/05 Install wheel axle (2) through wheel carriage (19) and install wheels (3) onto wheel axle (2) withspacers (17) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) section to tank and wheel carriage as shown. A deep socket is recommended. 8 7 6 Inst...

Page 15 - SECTION B: ATTACH THE BACKBOARD

15 11/05 ID# M731321 This is what your system will look likewhen you’ve finished this section. ITEMS REQUIRED FOR THIS SECTION SECTION B: ATTACH THE BACKBOARD 9/16” 1/2” 3/4” (2) 1/2" AND (2) 9/16" AND (2) 3/4" Wrenches (2) Socket Wrenches and Sockets AND/OR

Page 16 - Toward Pole; Upper Elevator tube; Toward Board

16 ID# M731321 11/05 44 2. 41 Identify elevator tubes (41 and 44). Toward Pole Upper Elevator tube Lower Elevator tube Assemble backboard brackets (29) using bolts (35), and nuts (9) as shown. 1. 35 35 35 35 29 29 Test fit bolts into holes of bracketsand carefully rock them in acircular motion to re...

Page 24 - Install Slam Jam Rim to Backboard

24 ID# M731321 11/05 31 32 36 20 30 36 38 40 A B C D E 36 36 40 38 Install Slam Jam Rim to Backboard A. Fit rim (20) securely into bracket (32) as shown. Allow T-bolt (36) to slip through center hole in rim (20). B. Install reinforcement bracket (31) onto T bolt (36) as shown.C. Install spring (30) ...

Page 27 - SAND; CAUTION

27 11/05 ID# M731321 15. 24 24 Roll completed assembly to desired position. Fill tank with water (approx. 30 gallons/115Liters) or sand (approx. 300 lbs./136 kg) and snap cap (24) in place. Peel protective film from surface of acrylic backboard prior to use. NOTE: ADD TWO GALLONS (7.6 LITERS) OFNON-...

Page 28 - DO NOT ALLOW

28 ID# M731321 11/05 Apply the height adjustment and moving label (25) to the front of the pole as shown. 17. 16. Pull trigger (33). Move elevator system up or down to desired height, release trigger (33) to locksystem into one of the five height settings. 33 10 ft. (3.05 m) 25 DO NOT ALLOW CHILDREN...