Huffy M671111 - Manuals - manualsarea.com

Page 3 - WARNING

07/05 ID# M671111 3 Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's fa...

Page 4 - SAFETY INSTRUCTIONS; MOVING SYSTEM

4 ID# M671111 07/05 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble th...

Page 5 - NOTICE TO ASSEMBLERS

07/05 ID# M671111 5 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water accor...

Page 6 - FRONT

6 ID# M671111 07/05 Get to know the basic parts of your basketball system..... FRONT PANEL BACKBOARD FRONT RIM BASE POLE

Page 10 - TOOLS REQUIRED FOR THIS SECTION; SECTION A: ASSEMBLE THE BASE; Wrenches

10 ID# M671111 07/05 TOOLS REQUIRED FOR THIS SECTION SECTION A: ASSEMBLE THE BASE And/Or: This is what your system will look likewhen you’ve finished this section: 1/2” 9/16” Wrenches (2) 1/2” (2) 3/4” (2) Socket Wrenches andSockets Extension Phillips-Head Screwdriver

Page 11 - Check the following pre-assembled base areas for tightness:

07/05 ID# M671111 11 1A. Check the following pre-assembled base areas for tightness: Eye bolts P/N 203452, Washer P/N 203218 , Nut P/N 203100, Carriage Bolts P/N 203223 . Eye boltsP/N 203452 WasherP/N 203218 NutP/N 203100 Front CoverP/N 206002 Pole BracketP/N 201581 Carriage BoltsP/N 203223 Hex Flan...

Page 12 - Check the following pre-assembled handle areas for tightness:

12 ID# M671111 07/05 Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolts P/N 203103 . Carriage Bolt P/N 203103 Nut P/N 203100 Nut P/N 203100 Handle, RightP/N 204856 Handle, LeftP/N 204855 Screw P/N 204803 Carriage Bolt P/N 203103 Height Adju...

Page 13 - Identify pole sections.

07/05 ID# M671111 13 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4)using a wood scrap as shown until the top pole no longer moves toward the poleidentification sticker on the middle pole. Identification Sticker TROUGH TROUGH TR...

Page 18 - SECTION B: ATTACH THE BACKBOARD; Head; Extension; Sawhorse

18 ID# M671111 07/05 TOOLS REQUIRED FOR THIS SECTION SECTION B: ATTACH THE BACKBOARD Phillips- Head Screwdriver This is what your system will look likewhen you’ve finished this section: Wrenches (2) 1/2"(2) 9/16” (2) 3/4” (2) SocketWrenches and Sockets And/Or 1/2” 9/16” Extension 3/4” Sawhorse 3...

Page 21 - Install Slam Jam Rim to Backboard

07/05 ID# M671111 21 3. 50 52 1 48 49 Install Slam Jam Rim to Backboard 34 51 49 1 52 A B C D E A Fit rim (34) securely into bracket (48) as shown. Allow T-bolt (49) to slip through center hole inrim (34). B Install reinforcement bracket (50) onto T-bolt (49) as shown. C Install spring (51) onto T-b...

Page 23 - Before going on to next step, set

07/05 ID# M671111 23 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 5. Support pole on sawhorse. Attach backboard assembly to top pole section (4)as shown. Install pole cap (38). Use caution; elevator assembly is heavy. 6. 7. Install upper elevator tubes (35) to triangleplate...

Page 24 - USE EYE PROTECTION; GALLONS OF

24 ID# M671111 07/05 8. Insert bolt (29) through left sideupper elevator tube (35), thenstretch spring (33) onto bolt (29).Insert bolt (29) through right sideupper elevator tube (35) andsecure with nut (31). 9. Roll completed assembly to desired position. Fill tank with water (approx.34 gallons (129...

Page 25 - SECTION C: APPLY HEIGHT AND MOVING LABEL & HEIGHT ADJUSTMENT; DO NOT ALLOW; Peel protective

07/05 ID# M671111 25 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height. SECTION C: APPLY HEIGHT AND MOVING LABEL &...