Huffy DC177 - Manuals - manualsarea.com

Page 2 - WARNING

2 P/N 211475 01/04 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or ...

Page 3 - SAFETY INSTRUCTIONS

01/04 P/N 211475 3 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water accord...

Page 5 - Item Qty

01/04 P/N 211475 5 Item Qty Part No. Description 1 1 908026 Top Pole Section 2 1 908107 Middle Pole Section (with Label) 3 1 908015 Bottom Pole Section 4 1 900223 Wheel Bracket 5 1 206940 Axle 6 2 226403 Wheel 7 2 206938 Pushnut 8 1 206660 Base 9 6 203156 Hex Bolt, 5/16-18 x 1 10 18 203218 Flat Wash...

Page 9 - ASSEMBLE THE POLES; Taped Reference

01/04 P/N 211475 9 SECTION A: ASSEMBLE THE POLES 2. WARNING LABEL 2 1 3 Taped Reference Mark Taped Reference Mark 1. Mark pole sections with tape (not supplied) as shown. Bounce middle pole (2) into top pole section(1) using a wood scrap as shown until toppole no longer moves toward pole tapedrefere...

Page 11 - ASSEMBLE THE BASE; a Hammer or

01/04 P/N 211475 11 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BASE This is what your system will look likewhen you’ve finished this section: a Hammer or Mallet (2) 1/2” AND (2) 9/16" Wrenches 9/16” 1/2” AND/OR (2) Socket Wrenches and ...

Page 15 - ASSEMBLE THE ELEVATOR & BACKBOARD; Wrenches

01/04 P/N 211475 15 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARD This is what your system will look likewhen you’ve finished this section: 9/16” 1/2” 3/4” (2) 1/2”, (2) 9/16"” AND (2) 3/4” Wrenches AND/OR (2) Soc...

Page 20 - Refer To

20 P/N 211475 01/04 8. Starting with nuts (11) flush against bracket (45) secure rim (40) and bracket tobackboard. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Rim mounting nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers here ...

Page 21 - Two people are recommended for this

01/04 P/N 211475 21 21 21 47 25 34 1 32 32 50 20 34 20 10. Support pole on sawhorse. Attach backboard assembly to top pole section (1)as shown. Install pole cap (25). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 50 33 20 21 1 21 33 20 32 51 11. Install upp...

Page 23 - SECURING THE SYSTEM

01/04 P/N 211475 23 1. SECTION D: SECURING THE SYSTEM Roll assembly to desired playing area. Secure assembly to ground using rope (56)and tie down stake (36). Fill base (8) with water (approx. 40 gallons) and snap fillcaps (37) in place. 56 36 37 8 37 DO NOT LEAVEASSEMBLY UNATTENDEDWHEN EMPTY; IT MA...

Page 24 - INSTALL FRONT COVER; STANDOFFS

24 P/N 211475 01/04 SECTION E: INSTALL FRONT COVER 1. Install front cover (38) by lining up stand-offs along the tank struts. Insert a tie strap(39) through the top two and bottom two stand offs. Wrap tie straps around tankstruts as shown and secure tightly. Trim excess of tie strap as shown in FIG....

Page 25 - Push second “arm” back and into ram as shown.; NET INSTALLATION

01/04 P/N 211475 25 1. Install clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” ofclip slightly so that second “arm” slides over the top of thefirst “arm” as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “body” ...

Page 26 - Insert net into bottom of clip as shown.

26 P/N 211475 01/04 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP 2. 40 57 58

Page 27 - APPLY HEIGHT AND MOVING LABEL

01/04 P/N 211475 27 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. While holdi...

Page 28 - HEIGHT ADJUSTMENT; Move elevator up or down to desired height.

28 P/N 211475 01/04 SECTION H: HEIGHT ADJUSTMENT 1. A. While holding handle, remove pin (27). B. Move elevator up or down to desired height. C. Replace pin (27) full length to lock system at desired height. 27 A. B. C. 51 DO NOT ALLOW CHILDREN TOADJUST HEIGHT. WARNING!