Huffy 89225 - Manuals - manualsarea.com

Page 2 - any excess paint from holes if necessary.

P/N 21154401 01/04 2 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular...

Page 3 - NOTICE TO ASSEMBLERS; SAFETY INSTRUCTIONS; This unit is intended for display purposes only and

3 P/N 21154401 01/04 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water acco...

Page 5 - PLASTIC SPACERS

5 P/N 21154401 01/04 Item #33 (12) Item #30 (4) Item #40 (4) HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #67 (2) PLASTIC SPACERS Item #7 (10) Item #4 (2) Item #22 (2) Item #13 (2) Item #27 (5) Item #18 (1) Item #59 (6) Item #65 (4) Item #2 (2) HARDWARE IDENTIFIER (SPRINGS & WASHERS) Item #63 (...

Page 6 - Display Stand - Top View

P/N 21154401 01/04 6 Install display boards in the marked locations. Each mounting location consists of a mounting polestub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate directionthe board is facing). Corner “2” 73256 Corner “4”80602 Corner “3” 61259 Corne...

Page 9 - STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY - Corner Location 1; Refer To

9 P/N 21154401 01/04 STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY - Corner Location 1 37 5. 38 38 24 24 17 17 Attach backboard support brackets (37) to thebackboard frame using bolts (24), spacers (38),and nuts (17) as shown . 29 29 39 39 59 37 42 Refer To Instructions Included With Rim Hardware For Rim A...

Page 13 - 4” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 2; Correctly identify each pole section.; Elevator tube

13 P/N 21154401 01/04 44” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 2 Correctly identify each pole section. ONLY THE TOP POLE SECTION (14) IS USED IN THIS ASSEMBLY. 1. BOTTOM POLE 43” MIDDLE POLE 43” TOP POLE 31” 14 Fit spacer (15) into pawl (19). Then continue to assemble as shown. Tighte...

Page 14 - notch of the bracket

P/N 21154401 01/04 14 Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolts (20),spacers (5, & 40), and nuts (42) as shown. Tighten completely. 5 . Secure pawl (19) in place with clevispin (31) and washers (6) as shown. 6 . Hook one end of the spring (36) into hole...

Page 17 - FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3.; TOP

17 P/N 21154401 01/04 Correctly identify each pole section. Poles have an identification stickerthat will be used as a reference pointin the next step. ONLY THE TOP POLE SECTION (50) IS USED IN THIS ASSEMBLY. FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3. Pole bracket will need to be lightly...

Page 18 - FAN BACKBOARD ASSEMBLY - Corner Location 4.; WARNING; Assemble fan backboard as shown below with a standard rim as shown.

P/N 21154401 01/04 18 FAN BACKBOARD ASSEMBLY - Corner Location 4. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble fan backboard as shown below with a standard rim as shown. 33 32 33 8 65 7 33 1. 34 8 10 66

Page 19 - Push second “arm” back and into ram as shown.

19 P/N 21154401 01/04 Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clipslightly so that second “arm” slides over the top of the first “arm” asshown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “bod...

Page 20 - Insert net into bottom of clip as shown.

P/N 21154401 01/04 20 Install net. Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP 12. 58 56 9