Huffy 600 - Manuals - manualsarea.com

Page 2 - NOTE: Not all items pictured are included with every model.

2 P/N 21163610 02/05 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circula...

Page 3 - WARNING

02/05 P/N 21163610 3 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces o...

Page 4 - SAFETY INSTRUCTIONS; MOVING SYSTEM

4 P/N 21163610 02/05 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble t...

Page 5 - NOTICE TO ASSEMBLERS

02/05 P/N 21163610 5 For more information on assembly, placement, properuse, and maintenance, visit The American BasketballCouncil website at http://www.smarthoops.com. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. ...

Page 6 - FRONT

6 P/N 21163610 02/05 Get to know the basic parts of your basketball system..... FRONT PANEL BACKBOARD FRONT RIM BASE POLE

Page 10 - SECTION A: ASSEMBLE THE BASE; Extension

10 P/N 21163610 02/05 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE And/Or: This is what your system will look likewhen you’ve finished this section: Item #39 Item #23 Item #16 Item #12 (1) Item #19 Item #21 Item #13 Item #20 Item #18 It...

Page 13 - Identify pole sections.

02/05 P/N 21163610 13 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4)using a wood scrap as shown until the top pole no longer moves toward the poleidentification sticker on the middle pole. Identification Sticker TROUGH Align di...

Page 18 - SECTION B: ATTACH THE BACKBOARD; Head; Sawhorse

18 P/N 21163610 02/05 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ATTACH THE BACKBOARD Phillips- Head Screwdriver This is what your system will look likewhen you’ve finished this section: Item #40 Item #39 Item #29 Item #19 Item #28 Item #26 Item #30 It...

Page 22 - Push second “arm” back and into ram as shown.

22 P/N 21163610 02/05 5. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clipslightly so that second “arm” slides over the top of the first“arm” as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “...

Page 23 - NET INSTALLATION

02/05 P/N 21163610 23 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 6. 34 42 43

Page 26 - SECTION C: APPLY HEIGHT AND MOVING LABEL & HEIGHT ADJUSTMENT; DO NOT ALLOW; Peel protective

26 P/N 21163610 02/05 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24).B. Move elevator up or down to desired height.C. Replace pin (24) full length to lock system at desired height. SECTION C: APPLY HEIGHT AND MOVING LABEL &...