Huffy 540D - Manuals - manualsarea.com

Page 2 - MOVING SYSTEM; SAFETY INSTRUCTIONS

2 ID# 211988 05 10/05 201261 3/99 1 3 2 MOVING SYSTEM 1. While holding pole, rotate basketball system forwarduntil wheels engage withground. 2. Move basketball system to desired location. 3. Carefully rotate basketball system upright. 4. Reattach ground restraint and check system for stability. 13 S...

Page 3 - NOTICE TO ASSEMBLERS

10/05 ID# 211988 05 3 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections, hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water acc...

Page 4 - FRONT

4 ID# 211988 05 10/05 Get to know the basic parts of your basketball system..... FRONT STRUTS BASE WHEEL CARRIAGE ASSEMBLY EXTENSION ARM POLE

Page 5 - WARNING; FAILURE TO FOLLOW THESE

10/05 ID# 211988 05 5 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. In the U.S.: 1-800-558-5234 and Canada Only: 1-800-284-8339 211239 2/05 See instruction...

Page 7 - SECTION A: ASSEMBLE THE BASE

10/05 ID# 211988 05 7 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE 9/16” and 1/2” 9/16” and 1/2” AND/OR This is what your system will looklike when you’ve finished thissection: Item #12 Item #10 Item #8 Item #14 Item #15 Item #19 Item #...

Page 8 - Remove contents from tank

8 ID# 211988 05 10/05 1. 1 6 5 Remove contents from tank 2. Install rod (5) through holes in bottom pole section (4) and eyebolt (6). 4 5 4 6

Page 9 - IMPORTANT! DO NOT OVER

10/05 ID# 211988 05 9 8 4 5 6 3. 9 11 1 12 11 10 10 4. 2 26 26 3 3 7 Install wheel axle (2) through wheel carriage (7) and install wheels (3) ontowheel axle (2) with spacers (26) as shown. Insert pole assembly into tankassembly as shown. Secure bottom pole (4) to tank and wheel bracket asshown, a de...

Page 11 - SECTION B: ASSEMBLE THE BACKBOARD; OR

10/05 ID# 211988 05 11 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION SECTION B: ASSEMBLE THE BACKBOARD 1/2” 1/2” OR This is what your system will look likewhen you’ve finished this section: Item #15 Item #19 Item #17 Item #29 Item #20

Page 12 - Peel protective; BOARD STYLE

12 ID# 211988 05 10/05 Do not use washers here on spring return style rims. 20 19 16 21 15 18 10 29 7. Install backboard assembly to the pole assembly as shown. Attach backboard andrim (16) to the extension arm (18) using bolts (20), spacers (21), washers (10, 19) andnuts (15) as shown. Tighten comp...

Page 13 - CLIP “ARM”

10/05 ID# 211988 05 13 8. WARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sureto follow directions carefully. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body...

Page 14 - NET INSTALLATION

14 ID# 211988 05 10/05 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 9. 16 17 23

Page 15 - SECTION B: SECURING THE SYSTEM

10/05 ID# 211988 05 15 1. 28 27 25 27 Place assembled unit to desired location. Fill tank with water (30 gallons/114 liters) or sand (360 lb./163 kg) and snap tank cap (28) in place. Insert T-strap (27) through slot on back of base as shown. Secure unit to ground by twisting tie down stake (25) into...

Page 16 - SECTION C: APPLY HEIGHT AND MOVING LABEL; Apply Height and Moving label on pole as shown.

16 ID# 211988 05 10/05 1. SECTION C: APPLY HEIGHT AND MOVING LABEL DIRECT MOUNT & EXT. ARM PORTABLE 201261 Eng: Dan\Tom1st Used:3/99 Size = 4" x 3" Corner Radius = 3/8" Die Cut Label 3.25 Mil Vinyl All Temp. Permanent Adhesive 1 Mil. Polypropolyne Overlaminate Illustrator 8.0 = EPS B...