Huffy 214953C - Manuals

Huffy 214953C – Manual in PDF format online.

Manuals:

Manual

Manual Huffy 214953C

Summary

Page 2 - any excess paint from holes if necessary.; cualquier exceso de pintura, si es necesario.

2 P/N 214953C 12/03 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular...

Page 3 - WARNING; FAILURE TO FOLLOW THESE WARNINGS MAY RESULT

12/03 P/N 214953C 3 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or...

Page 4 - enclosed postcard

4 P/N 214953C 12/03 For more information on assembly, placement, properuse, and maintenance, visit The American BasketballCouncil website at http://www.smarthoops.com. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. N...

Page 5 - SAFETY INSTRUCTIONS; Use caution when using this system.; excessive competitive play.

12/03 P/N 214953C 5 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. While holdi...

Page 6 - FRONT

6 P/N 214953C 12/03 Get to know the basic parts of your basketball system..... HUFFY HU FFY S PO R TS S PO R TS SUPPORT STRUT BACKBOARD FRONT RIM BASE POLE WHEELS ELEVATOR SYSTEM

Page 7 - PARTS LIST - See Hardware Identifier

12/03 P/N 214953C 7 PARTS LIST - See Hardware Identifier PARTS LIST - See Hardware Identifier Item Qty.Part No. Description 1 1 206336 Tank, (Gray) 2 2 206330 Wheel Axle, 4-1/4 Long 3 2 226401 Wheel, 4 “ (Black) 4 1 904847 Top Pole Section 5 1 908481 Middle Pole Section 6 1 908487 Bottom Pole Sectio...

Page 8 - You may have extra parts with this model.

8 P/N 214953C 12/03 HARDWARE IDENTIFIER (BOLTS) * You may have extra parts with this model. Item #8 (1) Item #14 (1) Item #15 (2) Item #18 (2) Item #21 (3) Item #25 (3) Item #30 (2) Item #47 (6) Item #48 (1) Item #37 (1) Item #31 (1)

Page 10 - ASSEMBLE THE BASE

10 P/N 214953C 12/03 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE This is what your system will look likewhen you’ve finished this section: (2) 1/2” AND (2) 9/16" Wrenches 9/16” 1/2” AND/OR (2) Socket Wrenches and Sockets Item #8 It...

Page 11 - Mark pole sections with tape as shown.

12/03 P/N 214953C 11 Insert axle rod (2) through wheel (3), as shown.Secure wheel assembly to tank (1) by tappingwheel downward with hammer, snapping it intoposition. Repeat for opposite side, thencarefully, turn tank (1) over. Remove all contents from underside oftank. Keep tank (1) bottom side up ...

Page 12 - While maintaining; While; WOOD SCRAP; POLE SECTIONS

12 P/N 214953C 12/03 IMPORTANT! Center alignment slot of lower polesection (6) in a lower hole ofmiddle pole section (5) as instep 3. While maintaining alignment, bounce top &middle pole assembly (4 & 5)onto lower pole section (6) asshown until top & middle poleassembly no longer movesto...

Page 13 - Insert pole assembly into tank assembly as shown.; DO NOT OVER

12/03 P/N 214953C 13 Insert pole assembly into tank assembly as shown. Install rod (7) through holes in bottom polesection (6) and eyebolt (8). DO NOT OVER TIGHTEN IMPORTANT!: DO NOT OVER TIGHTEN IMPORTANT!: TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULTIN SERIOUS I...

Page 15 - Tighten just until

12/03 P/N 214953C 15 19 21 21 19 19 20 20 19 17 22 22 23 23 Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), andnuts (20) as shown. Tighten just until washers (19) stop moving. IMPORTANT!: 17 16 26 24 24 27 25 FIG. A Assemble lanyard (27) to locking pin (26) as shown...

Page 18 - motion to ream out paint from holes if necessary; Refer to instructions; It is necessary for all

18 P/N 214953C 12/03 16. 36 20 35 21 34 37 Install spacers (36) onto backboard brackets (34) with bolts (37, 21) and lock-nuts(35, 20) as shown. Assemble lower elevator tubes (40) as shown. NOTE: Test fit bolts into holes of brackets (34) and carefully rock them in a circular motion to ream out pain...

Page 19 - Bend bracket (34) to line up with holes in backboard and secure.

12/03 P/N 214953C 19 Starting with nuts (16) flush against bracket (34), secure rim (42) and bracket tobackboard. Bend bracket (34) to line up with holes in backboard and secure. 18. 19. 34 16 42 16 IMPORTANT!: For spring loaded rimassembly, refer to instructions included withrim hardware. Mounting ...

Page 23 - Peel protective

12/03 P/N 214953C 23 26 26. 27. 28. HUFFY HUFFYSPORTS SPORTS 54 10 ft. (3.05 m) While holding handle, remove pin (26). Move elevator up or down to desiredheight. Replace pin (26) full length to locksystem at desired height. Apply height and transport label (54)to front of pole as shown. DO NOT LEAVE...

Page 24 - Poussez

24 P/N 214953C 12/03 Install net clips. Attachez les pinces de filet au cerceau, comme illustré. Die Netzhalteklammern wie gezeigt am Korbrand anbringen. Instale los sujetadores de la red en el borde, como se muestra. Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that ...

Page 25 - Insert net into bottom of clip as shown.

12/03 P/N 214953C 25 Install Net Installez le filet. Das Netz anbringen Instale la red. Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken. Introduzca la red en la parte inferior del sujetador como se mue...

Page 26 - AVERTISSEMENT; CONSIGNES DE SÉCURITÉ; Une Entreprise Huffy; Equipement de basketball port; VIS AUX

26 P/N 214953C 12/03 Numéro d’appel gratuit du service après-vente. Etats-Unis et Canada uniquement: 1-800-284-8339 Numéro vert international (France, Suisse) : 00 800 555 85234 TUFF STUFF® et les marques associées de Mattel, Inc. sont utilisées avec sa permission. Les produits Huffy ne sont nulleme...

Page 29 - ADVERTENCIA; INSTRUCCIONES DE SEGURIDAD; ESCRIBA SU NÚMERO DE MODELO:; Una Compañía Huffy; Manual del propiet; VISO P

29 12/03 P/N 214953C 00 800 555 85234 SI NO SE OBSERVAN ESTAS ADVERTENCIAS SE PUEDEN OCASIONAR LESIONES GRAVES Y/O DAÑOS MATERIALES El propietario debe asegurarse de que todos los jugadores onozcan y sigan estas reglas para la operación segura del istema . • NO SE CUELGUE del borde ni de ninguna par...

Page 32 - SICHERHEITSHINWEISE; ARNUNG; A Huffy Company; ragbares Basketball-System Benutzerhandbuch; Huffy steht zur Qualität seiner Produkte!; HINWEIS A

32 P/N 214953C 12/03 Universelle gebührenfreie Telefonnummer (Deutschland, Schweiz): 00 800 555 85234 SICHERHEITSHINWEISE Die meisten Verletzungen werden durch einen unvorschriftsmäßigen Gebrauch und/oder ein Mißachten der Sicherheitshinweise verursacht. Beim Gebrauch dieser Vorrichtung Vorsicht wal...