Huffy 211954E - Manuals - manualsarea.com

Page 2 - any excess paint from holes if necessary.

2 P/N 211954E 01/04 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular...

Page 3 - WARNING

01/04 P/N 211954E 3 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or...

Page 5 - SAFETY INSTRUCTIONS

01/04 P/N 211954E 5 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. While holdi...

Page 6 - FRONT

6 P/N 211954E 01/04 Get to know the basic parts of your basketball system..... SUPPORT STRUT BACKBOARD FRONT RIM BASE POLE WHEELS ELEVATOR SYSTEM

Page 7 - PARTS LIST - See Hardware Identifier

01/04 P/N 211954E 7 PARTS LIST - See Hardware Identifier Item Qty. Part No. Description 1 1 206336 Tank 2 2 206330 Wheel Axle, 4-1/4 Long 3 2 226401 Wheel, 4“ (Black) 4 1 904847 Top Pole Section 5 1 908024 Middle Pole Section 6 1 908487 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 2...

Page 9 - Mark pole sections with tape as shown.

01/04 P/N 211954E 9 Insert axle rod (2) through wheel (3), as shown.Secure wheel assembly to tank (1) by tappingwheel downward with hammer, snapping it intoposition. Repeat for opposite side, thencarefully, turn tank (1) over. Remove all contents from underside oftank. Keep tank (1) bottom side up 1...

Page 10 - While maintaining; While; POLE SECTIONS

10 P/N 211954E 01/04 IMPORTANT! Center alignment slot of lower polesection (6) in a lower hole ofmiddle pole section (5) as instep 3. While maintaining alignment, bounce top & middlepole assembly (4 & 5) ontolower pole section (6) as shownuntil top & middle pole assemblyno longer moves t...

Page 11 - Insert pole assembly into tank assembly as shown.; DO NOT OVER

01/04 P/N 211954E 11 Insert pole assembly into tank assembly as shown. Install rod (7) through holes in bottom polesection (6) and eyebolt (8). DO NOT OVER TIGHTEN IMPORTANT!: DO NOT OVER TIGHTEN IMPORTANT!: TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULTIN SERIOUS I...

Page 13 - Tighten just until

01/04 P/N 211954E 13 19 21 21 19 19 20 20 19 17 22 22 23 23 Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), andnuts (20) as shown. Tighten just until washers (19) stop moving. IMPORTANT!: 17 16 26 24 24 27 25 FIG. A Assemble lanyard (27) to locking pin (26) as shown...

Page 16 - It is necessary for all

16 P/N 211954E 01/04 47 42 40 41 40 55 57 57 34 39 Attach rim to board as shown. For spring loaded rim assembly, refer to instructionsincluded with rim hardware. Assemble lower elevator tubes (40) as shown. DO NOTovertighten. IMPORTANT!: Refer to instructions included with board and rim hardware for...

Page 22 - NET INSTALLATION

22 P/N 211954E 01/04 NET INSTALLATION Install net. Installez le filet. Das Netz anbringen Instale la red. Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken. Introduzca la red en la parte inferior del suj...