Huffy 211953C - Manuals - manualsarea.com

Page 2 - any excess paint from holes if necessary.

2 P/N 211953C 12/03 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular...

Page 3 - WARNING

12/03 P/N 211953C 3 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or...

Page 5 - SAFETY INSTRUCTIONS

12/03 P/N 211953C 5 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. While holdi...

Page 6 - FRONT

6 P/N 211953C 12/03 Get to know the basic parts of your basketball system..... HUFFY HU FFY S PO R TS S PO R TS SUPPORT STRUT BACKBOARD FRONT RIM BASE POLE WHEELS ELEVATOR SYSTEM

Page 7 - PARTS LIST - See Hardware Identifier

12/03 P/N 211953C 7 PARTS LIST - See Hardware Identifier PARTS LIST - See Hardware Identifier Item Qty.Part No. Description 1 1 206336 Tank, (Gray) 2 2 206330 Wheel Axle, 4-1/4 Long 3 2 226401 Wheel, 4 “ (Black) 4 1 904847 Top Pole Section 5 1 908481 Middle Pole Section 6 1 908487 Bottom Pole Sectio...

Page 10 - ASSEMBLE THE BASE

10 P/N 211953C 12/03 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE This is what your system will look likewhen you’ve finished this section: (2) 1/2” AND (2) 9/16" Wrenches 9/16” 1/2” AND/OR (2) Socket Wrenches and Sockets Item #8 It...

Page 11 - Mark pole sections with tape as shown.

12/03 P/N 211953C 11 Insert axle rod (2) through wheel (3), as shown.Secure wheel assembly to tank (1) by tappingwheel downward with hammer, snapping it intoposition. Repeat for opposite side, thencarefully, turn tank (1) over. Remove all contents from underside oftank. Keep tank (1) bottom side up ...

Page 12 - While maintaining; While; POLE SECTIONS

12 P/N 211953C 12/03 IMPORTANT! Center alignment slot of lower polesection (6) in a lower hole ofmiddle pole section (5) as instep 3. While maintaining alignment, bounce top &middle pole assembly (4 & 5)onto lower pole section (6) asshown until top & middle poleassembly no longer movesto...

Page 13 - Insert pole assembly into tank assembly as shown.; DO NOT OVER

12/03 P/N 211953C 13 Insert pole assembly into tank assembly as shown. Install rod (7) through holes in bottom polesection (6) and eyebolt (8). DO NOT OVER TIGHTEN IMPORTANT!: DO NOT OVER TIGHTEN IMPORTANT!: TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULTIN SERIOUS I...

Page 15 - Tighten just until

12/03 P/N 211953C 15 19 21 21 19 19 20 20 19 17 22 22 23 23 Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), andnuts (20) as shown. Tighten just until washers (19) stop moving. IMPORTANT!: 17 16 26 24 24 27 25 FIG. A Assemble lanyard (27) to locking pin (26) as shown...

Page 18 - motion to ream out paint from holes if necessary; Refer to instructions; It is necessary for all

18 P/N 211953C 12/03 16. 36 20 35 21 34 37 Install spacers (36) onto backboard brackets (34) with bolts (37, 21) and lock-nuts(35, 20) as shown. Assemble lower elevator tubes (40) as shown. NOTE: Test fit bolts into holes of brackets (34) and carefully rock them in a circular motion to ream out pain...

Page 19 - Bend bracket (34) to line up with holes in backboard and secure.

12/03 P/N 211953C 19 Starting with nuts (16) flush against bracket (34), secure rim (42) and bracket tobackboard. Bend bracket (34) to line up with holes in backboard and secure. 18. 19. 34 16 42 16 IMPORTANT!: For spring loaded rimassembly, refer to instructions included withrim hardware. Mounting ...

Page 23 - Peel protective

12/03 P/N 211953C 23 26 26. 27. 28. HUFFY HUFFYSPORTS SPORTS 54 10 ft. (3.05 m) While holding handle, remove pin (26). Move elevator up or down to desiredheight. Replace pin (26) full length to locksystem at desired height. Apply height and transport label (54)to front of pole as shown. DO NOT LEAVE...