Huffy 211387 - Manuals - manualsarea.com

Page 2 - MOVING SYSTEM; WARNING

2 P/N 211387 5/99 printed on recycled paper 1 3 2 1. While holding pole, rotatebasketball system forward untilwheels engage with ground. 2. Move basketball system todesired location. 3. Carefully rotate basketballsystem upright. 4. Reattach ground restraint andcheck system for stability. This unit a...

Page 3 - Correctly identify each pole section and

3 5/99 P/N 211387 printed on recycled paper 5 6 8 7 9 5 6 5 8 13 6 IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL 1. Remove contents from tank (1). Turn tank (1) bottom side up. Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank by tapping whe...

Page 6 - Attach pole assembly to pole bracket (10) as; KEEP UNNECESSARY

6 P/N 211387 5/99 printed on recycled paper Attach lower halves of backboardbrackets (23) to swivel bracket (21). NOTE: Keep hardware loose untilafter alignment in step 16. 13. 23 12 13 13 12 21 Attach upper pole mounting bracket (20) to swivelbracket (21) and fully tighten. 12. 21 22 8 12 20 Attach...

Page 7 - Attach bracket assembly to top pole; Attach back bracket (26) to backboard and

7 5/99 P/N 211387 printed on recycled paper NOTE: Two people recommended for thisprocedure. Attach bracket assembly to top pole section (5). Secure hardware as shown andtighten completely. Install pole cap (25). 14. PLAY POSITION STORAGE POSITION 24 13 7 25 5 8 Attach back bracket (26) to backboard ...

Page 8 - MAKE; INSIDE VIEW

8 P/N 211387 5/99 printed on recycled paper NOTE: Stretching netup then pulling side toside will help snap netunder center hook. IMPORTANT! MAKE SURE NET IS HELD BYALL THREE HOOKS ONTHE NET CLIP. Install net (35). 20. Install net clips (34) on rim (28). The two outer hooks on net clip must face towa...

Page 9 - NOTE: Two people recommended for this procedure.; Apply height adjustment label (40) to front of pole as shown.

9 5/99 P/N 211387 printed on recycled paper NOTE: Two people recommended for this procedure. Level backboard and rim adjust hardware from step 13 and 16. Tighten completely. Regulation rim height is 10 feet (3.05 m). 24. Apply height adjustment label (40) to front of pole as shown. 25. 10 feet (3.05...

Page 10 - TO PLACE IN THE STORAGE POSITION; HEIGHT ADJUSTMENT

10 P/N 211387 5/99 printed on recycled paper TO PLACE IN THE STORAGE POSITION Lower backboard and rim down to thelowest position (7 1/2 ’ (2.29 m)). Remove adjustment knob (9), washer(8), and carriage bolt (7). Carefullyrotate pole downward towardsground. D O N O T S T A N D B E H I N DSYSTEM WHEN P...

Page 11 - Remove tie down stake (37) from ground and

11 5/99 P/N 211387 printed on recycled paper 50" (127 cm) Secure screw hook (39) into wall, approximately 50” (127 cm) up from floor as shown. IMPORTANT! It is necessary to install screw hookinto a wall stud. Remove tie down stake (37) from ground and detach rope (36). Rotate system up onto the ...

Page 12 - PARTS LIST; HARDWARE IDENTIFIER; YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.

12 P/N 211387 5/99 printed on recycled paper PARTS LIST Item Qty. Part No. Description 1 1 206903 Tank 2 2 206327 Wheel Axle 3 2 226401 Wheel 4 1 908492 Bottom Pole Section 5 1 906643 Top Pole Section 6 1 906642 Middle Pole Section with Label 7 4 203231 Bolt, Carriage, 5/16-18 x 3-1/2 Long 8 12 2032...