Huffy 11S0057 - Manuals

Huffy 11S0057 – Manual in PDF format online.

Manuals:

Manual

Manual Huffy 11S0057

Summary

Page 2 - REQUIRED TOOLS AND MATERIALS:

2 P/N 211472 05/04 REQUIRED TOOLS AND MATERIALS: o (2) clés et/ou clés à douilles et douilles (douilles longues recommandées). Extension obligatoire. o (je 2) Schraubenschlüssel und/oder Steckschlüssel und Einsätze (tiefe Einsätze empfohlen). Verlängerung ist erforderlich. o (2 de cada una) llaves d...

Page 3 - IN; IN; NEED TRANSLATION PUT IN

05/04 P/N 211472 3 W A R N IN G F A IL U R E T O F O L L O W T H E S E W A R N IN G S M A Y R E S U L T IN S E R IO U S IN J U R Y A N D /O R P R O P E R T Y D A M A G E . O w n er m u st en su re th at al l p la ye rs kn o w an d fo llo w th es e ru le s fo r sa fe o p er at io n o f th e sy st em ...

Page 4 - NOTICE TO ASSEMBLERS; SAFETY INSTRUCTIONS

4 P/N 211472 05/04 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections, hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water accord...

Page 8 - move toward pole identification mark. Upright assembly.; SECTION A: ASSEMBLE THE POLES; WARNING; POLE

8 P/N 211472 05/04 Correctly identify each pole section. POLE IDENTIFICATION MARK Bounce pole top (4) and middle section (5) together as shown until they no longer move toward pole identification mark. Upright assembly. SECTION A: ASSEMBLE THE POLES WARNING LABEL 5 4 TOP MIDDLE BOTTOM 2. 1. 6 5 4 WO...

Page 9 - until they no longer move toward pole identification mark.

05/04 P/N 211472 9 Bounce top and middle pole assembly and bottom pole (6) together as shown until they no longer move toward pole identification mark. 4 5 6 3. WOOD SCRAP (NOT SUPPLIED) POLE IDENTIFICATION MARK POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: IMPORTANT!: Holes i...

Page 10 - SECTION B: ASSEMBLE THE BASE; OR

10 P/N 211472 05/04 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BASE This is what your system will look like whenyou’ve finished this section: 9/16” and 1/2” 9/16” and 1/2” OR Item #27 203063 Hex Locknut (Nylon Insert) 3/8 Item #10 Item #8 ...

Page 13 - TOP VIEW

05/04 P/N 211472 13 4. Secure tank struts (12 & 13) to pole. Nut (14) should be tightened until flush (even) with locknuts outer edge. 11 1 14 21 21 12 13 13 12 TOP VIEW TIGHTEN BOLT (11) INLOCK NUT (14) UNTILFLUSH (EVEN) WITH LOCKNUT’S OUTER EDGE. WARNING! 13 12 13 12

Page 14 - Secure non-secured ends of tank struts to tank as shown.

14 P/N 211472 05/04 17 9 23 21 5. Rotate all non-secured ends of tank struts to mounting holes in tank as shown. Secure non-secured ends of tank struts to tank as shown.

Page 15 - SECTION C: ASSEMBLE THE BACKBOARD

05/04 P/N 211472 15 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION SECTION C: ASSEMBLE THE BACKBOARD 1/2” 1/2” OR This is what your system will look like whenyou’ve finished this section: Item #21 Item #35 Item #38 #206249 hex hea d bolt,1/2 x 1 1 /4 Item #37 Item #22 Item #19 Item #3...

Page 16 - FRONT OF SYSTEM

16 P/N 211472 05/04 1. 29 35 32 32 30 Install screw jack support plates (29 & 30) topole using bolts (32) washers (31) and (35)as shown. FRONT OF SYSTEM 35 FRONT OF SYSTEM TOP VIEW 30 1 29 34 34

Page 17 - FRONT VIEW

05/04 P/N 211472 17 Attach height decal (31) toscrew jack (36). Align loweredge of decal with bottom ofblack indicator tube. 2. 4. 31 36 Place cover (40)over screw jack (36).Install pole cap (41). Center screw jack (35) between jack plates (29 & 30)) and secure as shown below.Do not overtighten....

Page 18 - DO NOT OVER

18 P/N 211472 05/04 ½ 8' 2.4m 8' 2.4m Secure upper elevator tubes (33) to pole assembly as shown. 32 35 Insert spacer (39) through topholes of height indicator cover(41) and screw jack assembly asshown. Align spacer (39) andscrew jack assembly betweenelevator tubes (33) and secure. 32 35 34 34 33 33...

Page 20 - STRAIGHT ON VIEW

20 P/N 211472 05/04 9 . Assemble backboard to elevator tubes (33 & 34) as shown. TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULT INSERIOUS INJURY AND/ORPROPERTY DAMAGE. WARNING! ½ 33 20 33 33 32 35 STRAIGHT ON VIEW Upper Tube Lower Tube Upper Tube Lower Tube DO N...

Page 21 - Push in direction indicated by arrow.

05/04 P/N 211472 21 10. Install clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clipslightly so that second “arm” slides over the top of the first“arm” as shown. Push in direction indicated by arrow. Push second “arm” back and into ram as shown. Twist “body”...

Page 22 - Insert net into bottom of clip as shown.; NET INSTALLATION

22 P/N 211472 05/04 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 10. 18 19 25

Page 23 - SECTION D: SECURING THE SYSTEM; IF FILLING WITH SAND:; FREEZE IS NOT

05/04 P/N 211472 23 1. Place assembled unit to desired location. Fill tank with water (28 gallons (114 liters)) or sand (360 lb. (163 kg)) and snap tank cap (28) in place. Secure system rigidly to a flat, solid (preferably concrete)surface using lag bolts or asimilar anchoring systemthrough holes in...

Page 24 - MOVING SYSTEM; SECTION E: APPLY HEIGHT AND MOVING LABEL

24 P/N 211472 05/04 SURE SHOT - 748 U-TURN : ADJUSTMENT PORTABLE 201254 Eng: Dan\Tom1st Used:2/99 Size = 4" x 5.5" Corner Radius = 3/8" Die Cut Label 3.25 Mil Vinyl All Temp. Permanent Adhesive 1 Mil. Polypropolyne Overlaminate Illustrator 8.0 = EPS Backing + 1/16 Circumference Rolls of ...

Page 25 - SECTION G: HEIGHT ADJUSTMENT; HOOK; DO NOT ALLOW

05/04 P/N 211472 25 Position looped end of height adjustment crank(42) onto hook as shown. Rotate crank handleto raise or lower backboard. View label (31) todetermine approximate backboard height. NOTE: If height adjustment is difficult tooperate, you may have over tightened theareas indicated. Regu...