Hoover WindTunnel- Manuals

Cleaner description The assembled cleaner will look like the drawing. 1. Handle 2. Self-propel button3. ON-OFF switch 4. Hose5. Tool cover6. Powered hand tool7. Final filter door8. Handle release lever: step on lever to lower handle to operating or low positions. 9. Edge groomers 10. Furniture guard...

Carrying cleaner The cleaner can be moved by usingthe carrying handle located on the back of the cleaner. Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating posi- tion for general operation on carpet and floors; low for reach...

Automatic brush roll Cleaning lightweight indicator flexible rugs When red is in the OFF window, brush Stand on one end rug move roll is STOPPED. cleaner toward other end or edge. When red in the ON window brush roll Before reaching edge, push down on is ROTATING. handle. This will lift up the front...

G Check bag indicator (some models only) The indicator (I) will begin to show red asthe filter bag fills with dirt. There are three conditions that will causethe indicator to become completely red: If the bag is full; change the bag. 2. If very fine materials have been picked up, clogging the bag po...

Replacing bag door Reposition bag door by placing tab on bottom of door into opening (C). Press top of door to snap securely shut. Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet. The secondary filter (A), located behind the grill in the bottom of bagc...

Removing belt Flat belt (B) operates the self-propel fea- ture and indirectly drives the brush roll. Remove used belt (B) from large pulley(C) and discard. Belt replacement The belts are located under the bottom plate of the cleaner and should be checked from time to time to be surethey are in good ...

Replacing brush roll Removing brush roll Slide Brush Roll Control (Fig. 2-9) to “Hard” (OFF) position. Turn cleaner over and remove bottom plate (Fig. 3-9). Lift up brush roll and slide V-belt (D) offbrush roll. Inspecting V-belt The V-belt is designed to last for a long time and is not normally rep...

6. With curved ends down, slide end plates (C) of brush roll into slots (E) on 7. Replace belt guard (B) making surenot to pinch brush bristles in guard. Turnagitator, making sure it rotates freely. Replace and tighten screws. 8. To replace bottom plate (A), insert the four tabs on edge of bottom pl...

Service To obtain approved HOOVER service and genuine HOOVER parts, locate thenearest Hoover Factory Service Center or Authorized Hoover WarrantyService Dealer (Depot) by: l checking the Yellow Pages under “Vacuum Cleaners Household” OR- * checking the list of Factory Service Centers provided with t...

Checking under bottom plate 5. Remove bottom plate ( Fig. 3-9) and brush roll (Fig. 3-15). Look into opening (F), in (G) and around liner (H), and remove any accumulated debris, If blockage occurs during powered hand tool use Disconnect powered hand tool from hose. Remove bottom plate, belt guardand...

Cleaner description The assembled cleaner will look like the drawing. 1. Handle 2. Self-propel button3. ON-OFF switch 4. Hose5. Tool cover6. Powered hand tool7. Final filter door8. Handle release lever: step on lever to lower handle to operating or low positions. 9. Edge groomers 10. Furniture guard...

Carrying cleaner The cleaner can be moved by usingthe carrying handle located on the back of the cleaner. Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating posi- tion for general operation on carpet and floors; low for reach...

Automatic brush roll Cleaning lightweight indicator flexible rugs When red is in the OFF window, brush Stand on one end rug move roll is STOPPED. cleaner toward other end or edge. When red in the ON window brush roll Before reaching edge, push down on is ROTATING. handle. This will lift up the front...

G Check bag indicator (some models only) The indicator (I) will begin to show red asthe filter bag fills with dirt. There are three conditions that will causethe indicator to become completely red: If the bag is full; change the bag. 2. If very fine materials have been picked up, clogging the bag po...

Replacing bag door Reposition bag door by placing tab on bottom of door into opening (C). Press top of door to snap securely shut. Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet. The secondary filter (A), located behind the grill in the bottom of bagc...

Removing belt Flat belt (B) operates the self-propel fea- ture and indirectly drives the brush roll. Remove used belt (B) from large pulley(C) and discard. Belt replacement The belts are located under the bottom plate of the cleaner and should be checked from time to time to be surethey are in good ...

Replacing brush roll Removing brush roll Slide Brush Roll Control (Fig. 2-9) to “Hard” (OFF) position. Turn cleaner over and remove bottom plate (Fig. 3-9). Lift up brush roll and slide V-belt (D) offbrush roll. Inspecting V-belt The V-belt is designed to last for a long time and is not normally rep...

6. With curved ends down, slide end plates (C) of brush roll into slots (E) on 7. Replace belt guard (B) making surenot to pinch brush bristles in guard. Turnagitator, making sure it rotates freely. Replace and tighten screws. 8. To replace bottom plate (A), insert the four tabs on edge of bottom pl...

Service To obtain approved HOOVER service and genuine HOOVER parts, locate thenearest Hoover Factory Service Center or Authorized Hoover WarrantyService Dealer (Depot) by: l checking the Yellow Pages under “Vacuum Cleaners Household” OR- * checking the list of Factory Service Centers provided with t...

Checking under bottom plate 5. Remove bottom plate ( Fig. 3-9) and brush roll (Fig. 3-15). Look into opening (F), in (G) and around liner (H), and remove any accumulated debris, If blockage occurs during powered hand tool use Disconnect powered hand tool from hose. Remove bottom plate, belt guardand...