Hoover U5361950- Manuals

Handle position For ease in sliding knob, place handlein the upright position (C). The nozzle will not move into theadjusted position until the cleanerhandle is lowered to the operatingposition (D). Settings For maximum cleaning performance, the following carpet height settings arerecommended. • Low...

7 Edge cleaning Edge cleaning is provided on both sidesof the nozzle to remove dirt in carpetnear baseboards and furniture. Guide either side of nozzle parallel toedge of carpet or furniture. Cleaning tools Tools allow for cleaning surfaces abovethe floor and for reaching hard to cleanareas. The cle...

3. Maintenance When to empty It is recommended that the dirt cup beemptied before the dirt reaches the dirtopening on back of dirt cup (Fig. 3-1) orafter every use if preferred. CAUTION: Very fine materials, suchas face powder or cornstarch, mayseal the filter and cause loss of suc-tion. When using ...

9 3-10 3-6 3-5 3-7 3-8 3-9 3-11 Pull up on pre-filter assembly. Slide it outof cup. Replace dirt cup. Filter assembly How to clean filterassembly Remove dirt cup and dirt cup lid asdescribed in “How to empty dirt cup”. Pivot pre-filter assembly toward center ofcup. Remove main filter from pre-filter...

G Remove lens - Disconnect clean- er from electrical outlet. Using a screwdriver, remove the twoscrews as shown and lift off lens. 3-16 3-15 10 Secondary and finalfilters Cleaning secondary filter Disconnect cleaner from electricaloutlet. The secondary filter (G) , located under- neath the retainer ...

11 Continued ➜ 3-17 3-18 Remove agitator brush roll Remove agitator and used belt. Discard used belt. Replace lens - Reposition lens and secure with the two screws. How to replace Disconnect cleaner from electricaloutlet. Remove bottom plate Place handle in low position and turncleaner over so botto...

12 3-24 3-25 The agitator brush roll When to replace When agitator brushes are worn, theagitator should be replaced. To check condition of brushes, discon- nect cleaner from electrical outlet. Move edge of a card across bottomplate while turning agitator. To maintaincleaning effectiveness, replace a...

Handle position For ease in sliding knob, place handlein the upright position (C). The nozzle will not move into theadjusted position until the cleanerhandle is lowered to the operatingposition (D). Settings For maximum cleaning performance, the following carpet height settings arerecommended. • Low...

7 Edge cleaning Edge cleaning is provided on both sidesof the nozzle to remove dirt in carpetnear baseboards and furniture. Guide either side of nozzle parallel toedge of carpet or furniture. Cleaning tools Tools allow for cleaning surfaces abovethe floor and for reaching hard to cleanareas. The cle...

3. Maintenance When to empty It is recommended that the dirt cup beemptied before the dirt reaches the dirtopening on back of dirt cup (Fig. 3-1) orafter every use if preferred. CAUTION: Very fine materials, suchas face powder or cornstarch, mayseal the filter and cause loss of suc-tion. When using ...

9 3-10 3-6 3-5 3-7 3-8 3-9 3-11 Pull up on pre-filter assembly. Slide it outof cup. Replace dirt cup. Filter assembly How to clean filterassembly Remove dirt cup and dirt cup lid asdescribed in “How to empty dirt cup”. Pivot pre-filter assembly toward center ofcup. Remove main filter from pre-filter...

G Remove lens - Disconnect clean- er from electrical outlet. Using a screwdriver, remove the twoscrews as shown and lift off lens. 3-16 3-15 10 Secondary and finalfilters Cleaning secondary filter Disconnect cleaner from electricaloutlet. The secondary filter (G) , located under- neath the retainer ...

11 Continued ➜ 3-17 3-18 Remove agitator brush roll Remove agitator and used belt. Discard used belt. Replace lens - Reposition lens and secure with the two screws. How to replace Disconnect cleaner from electricaloutlet. Remove bottom plate Place handle in low position and turncleaner over so botto...

12 3-24 3-25 The agitator brush roll When to replace When agitator brushes are worn, theagitator should be replaced. To check condition of brushes, discon- nect cleaner from electrical outlet. Move edge of a card across bottomplate while turning agitator. To maintaincleaning effectiveness, replace a...