Hoover Breathe Easy- Manuals

5 1-14 Push bolt into hole on lower f ront of handle. If bolt will not go through hole easily,check the following: • the bracket is properly positioned (Fig.1-9) • the handle is pushed completely down(Fig. 1-13) 1-15 Place n u t in recessed area at back of h a n d l e . Hold nut in place while tight...

6 1-20 1-21 1-22 1-19 U T E C B A Align opening (U) in filter bag with dirttube (T) inside bag compartment. Push bag collar firmly onto dirt tube. Tuck top and bottom of bag into bagcompartment. To replace bag door, insert the tabs (V)on bottom of bag door into the slots onbag compartment. Make sure...

2-1 2-2 2-3 2. How to use r 1 4 3 6 8 7 9 10 13 12 11 15 14 2 2 16 17 2 18 19 20 5 15 The assembled cleaner will look like the drawing. 1. Handle2. Cord hooks : wrap cord around hooks for storage. The top hook can be rotated right or leftfor easy cord release. 3. Extra belt storage: inside bag compa...

2-4 B A C D 2-5 2-6 2-7 To move your cleaner from room to room, put handle in upright position, tiltcleaner back on rear wheels and pushforward. The cleaner can also be moved by liftingit as shown. For ease in sliding the control, the han-dle should be in the upright position (C). The front of the c...

10 The following sections are concernedwith proper maintenance of the cleaner.Familiarize yourself with these homemaintenance tasks and keep this owner’smanual in a convenient place where youcan refer to it when needed. Proper useand care of your cleaner will ensure con-tinued cleaning effectiveness...

11 3-4 3-5 3-6 3-7 3-8 3-9 The headlight How to replace Disconnect cleaner from electrical outlet. Belt replacement How to replace G H F What to buy This cleaner uses a 12 volt, wedge base type 912 bulb, Hoover P a r t No. 27313-101. Removing hood Place handle in low position and turn clean- er over...

12 3-10 3-11 3-12 3-13 I J Installing brush roll Grasp brush roll firmly and fit it into position by first sliding belt side into therectangular slot (I) on side of cleaner. Pull other side of brush roll (J) intoplace. Turn brush roll making sure belt is notpinched between brush roll and cleaner bas...

13 Problem: Cleaner won’t run Problem: Cleaner won’t pick up Problem: Cleaning tools won’tpick up Possible cause Possible solution • Not firmly plugged in.• Plug in firmly. • No voltage in wall plug.• Check fuse or breaker. • Blown fuse/tripped breaker.• Replace fuse/reset breaker. Possible cause Po...

5 1-14 Push bolt into hole on lower f ront of handle. If bolt will not go through hole easily,check the following: • the bracket is properly positioned (Fig.1-9) • the handle is pushed completely down(Fig. 1-13) 1-15 Place n u t in recessed area at back of h a n d l e . Hold nut in place while tight...

6 1-20 1-21 1-22 1-19 U T E C B A Align opening (U) in filter bag with dirttube (T) inside bag compartment. Push bag collar firmly onto dirt tube. Tuck top and bottom of bag into bagcompartment. To replace bag door, insert the tabs (V)on bottom of bag door into the slots onbag compartment. Make sure...

2-1 2-2 2-3 2. How to use r 1 4 3 6 8 7 9 10 13 12 11 15 14 2 2 16 17 2 18 19 20 5 15 The assembled cleaner will look like the drawing. 1. Handle2. Cord hooks : wrap cord around hooks for storage. The top hook can be rotated right or leftfor easy cord release. 3. Extra belt storage: inside bag compa...

2-4 B A C D 2-5 2-6 2-7 To move your cleaner from room to room, put handle in upright position, tiltcleaner back on rear wheels and pushforward. The cleaner can also be moved by liftingit as shown. For ease in sliding the control, the han-dle should be in the upright position (C). The front of the c...

10 The following sections are concernedwith proper maintenance of the cleaner.Familiarize yourself with these homemaintenance tasks and keep this owner’smanual in a convenient place where youcan refer to it when needed. Proper useand care of your cleaner will ensure con-tinued cleaning effectiveness...

11 3-4 3-5 3-6 3-7 3-8 3-9 The headlight How to replace Disconnect cleaner from electrical outlet. Belt replacement How to replace G H F What to buy This cleaner uses a 12 volt, wedge base type 912 bulb, Hoover P a r t No. 27313-101. Removing hood Place handle in low position and turn clean- er over...

12 3-10 3-11 3-12 3-13 I J Installing brush roll Grasp brush roll firmly and fit it into position by first sliding belt side into therectangular slot (I) on side of cleaner. Pull other side of brush roll (J) intoplace. Turn brush roll making sure belt is notpinched between brush roll and cleaner bas...

13 Problem: Cleaner won’t run Problem: Cleaner won’t pick up Problem: Cleaning tools won’tpick up Possible cause Possible solution • Not firmly plugged in.• Plug in firmly. • No voltage in wall plug.• Check fuse or breaker. • Blown fuse/tripped breaker.• Replace fuse/reset breaker. Possible cause Po...