Page 2 - WARNING; IMPORTANT SAFETY INSTRUCTIONS; READ ALL INSTRUCTIONS
Page 2 ■ ■ ■ ■ ■ Introduction ................................................................................................................................................................. 2 ■ ■ ■ ■ ■ Impor tant Safety Instructions ....................................................................
Page 4 - SYMBOLS; SYMBOL; SAVE THESE INSTRUCTIONS
Page 4 Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION Safety Alert Symbol Indicates danger, warning or caution. It meansat...
Page 5 - INSTRUCTIONS
Page 5 Weight - (without fuel) ............................................................................................................................ 9.1 lbs. (4.13 kg.) Cutting swath .................................................................................................................
Page 6 - ASSEMBLY; ATTACHING THE STORAGE HANGER
Page 6 ASSEMBLY ATTACHING THE POWER HEAD TO THETRIMMER ATTACHMENT See Figure 5. REMOVING THE ATTACHMENT FROM THEPOWER HEAD For removing or changing the attachment: 1. Loosen the knob. 2. Push in the button and twist the shafts to remove and separate ends. ATTACHING THE STORAGE HANGER See Figure 6. T...
Page 8 - FUELING AND REFUELING THE TRIMMER; OPERATING THE TRIMMER; OPERATION
Page 8 FUELING AND REFUELING THE TRIMMER FUEL MIXTURE This product is powered by a 2-cycle engine and requirespre-mixing gasoline and 2-cycle oil. Pre-mix unleadedgasoline and 2-cycle engine oil in a clean 1 gallon containerapproved for gasoline. Recommended fuel: This engine is certified to operate...
Page 9 - ADVANCING THE STRING; CUT OFF BLADE
Page 9 ADVANCING THE STRING ADVANCING STRING USING THE EZ LINE™ TAPADVANCE SYSTEM String advance is controlled by tapping string head on grasswhile running engine at full throttle. 1. Run engine at full throttle. 2. Tap string head on ground to advance string. String advances each time the head is t...
Page 10 - STARTING AND STOPPING
Page 10 1 2 3 STARTING AND STOPPING See Figure 8 and 9. TO START A COLD ENGINE: 1. Lay the trimmer on a flat, bare surface. 2. Make sure the switch is in the run “I” position. 2. Push the primer bulb 8 to 10 times. 3. Set the choke lever to the choke position . 4. Squeeze the throttle trigger to the...
Page 11 - MAINTENANCE; SPOOL REPLACEMENT
Page 11 WARNING: Use only original manufacturer's replacement parts,accessories and attachments. Failure to do so maycause poor performance, possible injury and mayvoid your warranty. Fig. 10 Fig. 11 SPOOL RETAINER SPRING SLOTS STRING HEAD EYELETS DRIVESHAFT MAINTENANCE You can often make adjustment...
Page 14 - TROUBLESHOOTING
Page 14 PROBLEM POSSIBLE CAUSE SOLUTION 1. To check for spark: Disconnect the spark plug wire. Reattach the spark plug wire and lay sparkplug on metal cylinder. Pull the starter rope andwatch for spark at spark plug tip. If there is nospark, repeat test with a new spark plug. 2. Push primer bulb unt...
Page 16 - WARRANTY; LIMITED WARRANTY STATEMENT
Page 16 WARRANTY LIMITED WARRANTY STATEMENT Homelite Consumer Product, Inc. warrants to the original retailpurchaser that this HOMELITE product is free from defect inmaterial and workmanship and agrees to repair or replace, atHomelite Consumer Products, Inc.’s discretion, any defectiveproduct free o...
Page 19 - SERVICE PARTS
Page 19 SERVICE PARTS P OPTIONAL MUFFLER GUARD G E H K F Q L J O N A C M B D For product information, technical help,dealer locations or parts ordering informationvisit our website at: www.homelite.com orcall 1-800-chainsaw (1-800-242-4672). P/N DESCRIPTION A. UP04634 Muffler Assembly w/Gasket Inclu...
Page 20 - CALIFORNIA PROPOSITION 65; SERVICE
983000-294 HOMELITE CONSUMER PRODUCTS, INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207, Anderson, SC 29622 Phone 1-800-chainsaw (1-800-242-4672) www.homelite.com OPERATOR'S MANUAL 25cc String TrimmerVersa Tool™ Model No. UT20811E WARNING: The engine exhaust from this product con...