Hitachi CP-X3014WN - Manuals

Page 2 - Data Data; Initial set signals

2 Initial set signals Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Data Data H. Sync. V. Sync. Sync (A) Sync (a) Active video (c) Resolution (H x V) Horizontal signal timing (μs) Vertical signal timing (lines) Signal mode (A) (B) (C) (D) (a) (b) (c) (d) 720 x 400 2....

Page 3 - Connection to the ports; NOTICE; COMPUTER IN1; or; MONITOR OUT

3 A COMPUTER IN1, B COMPUTER IN2, C MONITOR OUT D-sub 15pin mini shrink jack <Computer signal>• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)• H/V. sync. signal: TTL level (positive/negative)• Composite sync. signal: TTL level <Component video signal>• Video sign...

Page 8 - RS-232C Communication; Connection; Turn off the projector and the computer.; CONTROL; CONTROL

8 ① ② ⑥ ⑦ ⑧ ⑨ ⑤ ④ ③ CD (1) (1) − RD(2) (2) RD TD (3) (3) TD DTR (4) (4) − GND (5) (5) GND DSR (6) (6) − RTS (7) (7) RTS DTS (8) (8) CTS RI (9) (9) − RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with ...

Page 9 - Communicaion settings; Byte Number; above

9 RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps,8N1 2. Command for mat ("h" shows hexadecimal) Byte Number 0 1 2 3 4 5 6 7 8 9 10 11 12 Command Action Header Data Header code Packet Data size CRC ﬂag Action Type Setting code L H L H L H L H L H L H <SET>C...

Page 11 - LAN; port to the computer's; USB TYPE A; NOTE; Command Control via the Network

11 When the projector connects network, the projector can be controlled with RS-232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17 ). Command Control via the Network LAN cable (CAT-5 or greater) LAN LAN Conne...

Page 12 - Communicaion Por t; The following two ports are assigned for the command control.; Port Settings; Security Settings

12 Communicaion Por t The following two ports are assigned for the command control. TCP #23TCP #9715 Conﬁgure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Por...

Page 13 - Command control settings; Header; Refer to RS-232C Communication command format (

13 Command Control via the Network (continued) Command control settings [TCP #23] 1. Command for mat Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the sa...

Page 14 - “password” and it becomes “a572f60cpassword”.

14 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (1) ACK reply : 06h + ××h ( ××h : connection ID ) (2) NAK reoly : 15h + ××h(3) Error reply : 1Ch +...

Page 15 - Network Guide; OPTION menu; Network Bridge Communication

15 This projector is equipped with NETWORK BRIDGE function.When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS-232C communication can be controlled from the computer as a network terminal.For details, see th...

Page 16 - Communication settings; Operating; Transmission method

16 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. ( OPTION menu - SERVICE - COMMUNICATION in the Operating Guide ) Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (ﬁxed) PARITY NONE/ODD/EVEN Start bit 1 bit (ﬁxed) S...

Page 31 - PJLink command

31 PJLink command PJLink command POWR Power Contorol 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 11 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B...