Hilti 3563753 - Manuals - manualsarea.com

Page 3 - Information about the documentation; DANGER

English 1 1 Information about the documentation 1.1 About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the produ...

Page 5 - Safety; Personal safety

English 3 1.5 Product information products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can pres...

Page 8 - English

6 English Printed: 17.05.2018 | Doc-Nr: PUB / 5252092 / 000 / 06

Page 10 - Description; Product overview

8 English 3 Description 3.1 Product overview 3.1.1 Gasoline-powered cut-off saw Printed: 17.05.2018 | Doc-Nr: PUB / 5252092 / 000 / 06

Page 12 - Intended use

10 English 3.1.2 Saw trolley (accessory) @ Grip ; Throttle trigger = Cutting depth adjustment % Hold-down device & Water tank ( Water connection ) Axial adjustment + Throttle cable § Machine cradle 3.2 Intended use The product described is a gasoline-powered cut-off saw for the wet or dry cuttin...

Page 13 - Technical data

English 11 3.3 Recommendations for use We recommend: • Use of the wet cutting method is preferable in order to reduce the amount of dust produced when cutting. By using the self-priming water pump (accessory) you can work without need for a water supply pipe. The water can be drawn, for example, dir...

Page 14 - Before use; influences the running and life expectancy of the engine.

12 English DSH 900 35/14" / DSH 900-X 35/14" DSH 900 40/16" / DSH 900-X 40/16" Cubic capacity 5.3 in³ (87 cm³) 5.3 in³ (87 cm³) Weight without cutting disc, fuel tank empty 26.5 lb (12.0 kg) 27.3 lb (12.4 kg) Weight with saw trolley, without cutting disc, fuel tank empty 94.8 lb (43....

Page 20 - Operation; Starting the engine

18 English 6 Operation 6.1 Starting the engine DANGER Risk of asphyxiation. Carbon monoxide, unburned hydrocarbons and benzene in the exhaust gas may cause asphyxiation. ▶ Don’t work in closed rooms, trenches or pits and make sure the area is well ventilated. WARNING Risk of burning injury. The exha...

Page 21 - Checks after starting the engine

English 19 ▶ If the following conditions are met, also take this action: Conditions : The engine is hot. ▶ Pull the choke lever upwards and then push it back down again. ◁ This engages half throttle. The choke is not engaged. ▶ Check that the cutting disc is free to rotate. ▶ Position your right foo...

Page 23 - Reasons for the cutting disc stalling:; Care and maintenance; WARNING

English 21 Reasons for the cutting disc stalling: • The cut is too deep. • The kerf closes (e.g. when cutting pipes or slabs). • The cutting disc is off-square in the kerf. • The cutting disc is unsuitable for the job (the cutting disc becomes clogged). • The cutting disc is inserted too quickly int...

Page 28 - Transport and storage; Troubleshooting

26 English 8 Transport and storage 8.1 Transportation in a vehicle DANGER Risk of fire and explosion. If the product tips over during transport, fuel may run out of the fuel tank. ▶ Empty the product’s fuel tank completely before packing and shipping it. ▶ Transport the product, as far as possible, ...

Page 32 - In Canada; Mississauga, ON L5N 6S2; Hilti; comments and oral or written agreements concerning warranties.

30 English Hilti Inc. 7250 Dallas Parkway, Suite 1000 Plano, TX 75024 [email protected] In Canada : 800.343.4458 Hilti (Canada) Corporation 2360 Meadowpine Blvd Mississauga, ON L5N 6S2 [email protected] [email protected] This constitutes Hilti ’s entire obligation with regard to warranty and superse...