Hifonics ZRX1200.2 - Manuals

Page 2 - INDEX PAGE; Full range stereo / mono; ZEUS HIGH PERFORMANCE AMPLIFIERS

INDEX PAGE General Installation Procedure..........................................................................................................................................................................................1 Amplifier Feature Descriptions............................................

Page 3 - GENERAL INSTALLATION PROCEDURE; System Design; Power and ground connections; WIRE GAUGE; ZEUS

GENERAL INSTALLATION PROCEDURE 1 System Design Installation The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher pow...

Page 4 - AMPLIFIER FEATURE DESCRIPTIONS

AMPLIFIER FEATURE DESCRIPTIONS ZEUS ZRX AMPLIFIERS: 2 ZRX1000.1D / ZRX1500.1D / ZRX2000.1D / ZRX3000.1D 1-CHANNEL AMPLIFIERS The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of controls.1 set for channels 1 & 2 and 1 set for channels 3 & 4.In add...

Page 5 - “Setting up systems after installation for best performance”; FULL RANGE STEREO; MONO

3 ZRX500.2 / ZRX1200.2 2-CHANNEL AMPLIFIER APPLICATIONS 4. Line Level: This is the most basic application for the ZRX Series 2 channel amplifiers. Refer to the section “Setting up systems after installation for best performance” 1. Interconnect cable checklist: Connect the LINE INPUTS to the Radio/C...

Page 6 - CHANNEL FULL RANGE SYSTEM

POWER INPUT GND REM BA TT+12V CH 1/2 SPEAKER OUTPUT CH 3/4 RIGHT LEFT RIGHT LEFT - + - + - + - + BRIDGED BRIDGED FUSE ZRX600.4 / ZRX1000.4 / ZRX2000.4 4-CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYSTEM 2 or 3 CHANNEL SYSTEM - HI PASS: N/A Here we show how to use the 4 channel amplifiers as...

Page 7 - Front/Rear high pass, using a 2 channel amplifier for mono sub bass; the inputs of the 4 channel amplifier as shown.

5 Front/Rear high pass, using a 2 channel amplifier for mono sub bass Channels 1/2: The combination of a 2 and a 4 channel amplifier, utilizing their built in - HI PASS: 100 Hz crossovers, makes it a snap to put together a full system with front and rear highs, with mono sub bass. LOW PASS: N/A Inte...

Page 8 - Basic application; FULL RANGE; CHASSIS GROUND

ZRX1000.1D / ZRX2000.1D / ZRX3000.1D 1-CHANNEL AMPLIFIER APPLICATIONS 6 POWER INPUT BA TT+12V GND SPEAKER OUTPUT REM - - + + POWER INPUT GND REM BA TT+12V SPEAKER OUTPUT - - + + FUSE Basic application Crossover frequency control checklist: These sub bass amplifiers can be used in any of the bi-ampli...

Page 10 - SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE

8 SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE ZRX1000.1D / ZRX1500.1D / ZRX2000.1D / ZRX3000.1D General: At this point you are ready to get more specific on the settings for your amplifier. Subsonic: This setting acts as a low frequency cut off for your system bass reproduction. The p...

Page 11 - TROUBLESHOOTING A SYSTEM; Causes of overheating:

TROUBLESHOOTING A SYSTEM 9 The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the PROTECT system built into all Hifonics amplifiers The diagnostic system will shut down the amplifier, until rese...

Page 12 - Maxxsonics Limited Warranty; FOR EXTENDED WARRANTY INFORMATION, PLEASE VISIT

10 As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch and Hifonics car audioproducts, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifierto be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of ...