Heatiator I80 - Manuals

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 5 2 2 Getting Started A. Design and Installation Considerations Draft is the pressure difference needed to vent fi replaces successfully. Considerations for successful draft include: • Preventing negative pressure• Location of fi replace and chimney B...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 6 Location of the fi replace and chimney will affect performance. As shown in Figure 2.1 the chimney should: • Be installed through the warm airspace enclosed by the building envelope. This helps to produce more draft, especially during lighting and d...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 7 Non-combustibleroof flashing maintains minimum clearance around chimney Additional lateral support for chimney above roof (or enclosed in chase) if needed Ceiling firestop on floor of attic Support straps on rafter supports chimney (not shown) Termi...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 8 Before beginning the installation be sure the following tools and building supplies are available: Reciprocating saw Framing material Pliers High temp caulking material Hammer GlovesPhillips screwdriver Framing square Flat blade screwdriver Electric...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 9 3 3 Framing and Clearances A. Selecting Fireplace Location Several options are available to you when choosing a loca-tion for your fi replace. This fi replace may be used as a room divider, installed along a wall, across a corner or used in an exter...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 11 C. Sidewalls/Surrounds Adjacent combustible side walls must be located a minimum of 24 in. (610 mm) from the fi replace opening. See Figure 3.3. If you are using a decorative surround constructed of combustible material, it must be located within t...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 12 E. Construct the Chase A chase is a vertical boxlike structure built to enclose the fi re- place and/or its vent system. Vertical chimneys that run on the outside of a building must be installed inside a chase. Construction of the chase may vary wi...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 13 A. Install the Outside Air Kit The outside air assembly is factory installed on the left side of the fi replace. The kit is an optional component and its use is highly recommended to minimize the effect of negative pressure within the structure. • ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 14 Handle up - open Handle down - closed Figure 4.4 Locating the Outside Air Control Outlet placed higher than 3 ft below the termination cap Attic space Garage or combustible liquids storage Outlet blocked by snow, leaves, etc. Clear area outside hou...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 15 B. Secure the Fireplace • Position the Fireplace This fi replace may be placed on either a combustible or noncombustible continuous fl at surface. Follow the in- structions for framing in Section 3.D. Slide the fi replace into position. Be sure to ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 16 • Remove fi replace from pallet. The fi replace is attached to pallet with two brackets on each side and rear of outer shell. See Figure 4.11. Remove screws from bracket, pallet and fi replace. Replace screws removed from fi replace. Slide fi repla...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 18 Note: When elevating the fi replace above the hearth exten- sion the front of the elevated platform must be protected with a protective metal hearth strip as shown in Figure 4.19. Raised Platform Floor 2 in. (51 mm) 1 in. (25 mm) min. overlap 2 in....

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 19 NOTE: • Chimney performance may vary. • Trees, buildings, roof lines and wind conditions affect performance. • Chimney height may need adjustment if smoking or overdraft occurs. Chimney must extendbeyond combustibleroof structure Maintain minimumhe...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 20 A. Chimney Requirements Vertical distances are measured from the base of the fi re- place as shown in Figure 5.2. To determine the chimney components needed to complete your particular installation, follow the steps below: • Determine the total ver...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 22 C. Assemble the Chimney Sections Attach either a straight chimney section or an offset to the top of the fi replace (depending on your installation require- ment, US only). Chimney sections are locked together by pushing downward until the top sect...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 23 6 Tabs bent in 90° Tabs bent in to rest against pipe Attic Insulation Shield Ceiling Firestop 13 in. (330 mm) 17 in. (432 mm) diameter Insulation Insulation Pipe Pipe Figure 5.7 Install Attic Insulation Shield Above the Ceiling 6 Tabs bent in 90° T...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 24 Ceiling Firestop Straps Optional Additional Support Joint Band (Optional) Figure 5.9 Secure the Chimney Fire Risk • Secure offsets with screws (not to exceed 3/4 in./19 mm in length). WARNING • Secure returns with strapping.• Straight chimney secti...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 25 6 6 Complete the Enclosure A. Chimney Termination Chimney Termination Requirements (See Figure 6.1) • Must have a cap approved and listed for this fi replace system • Must not be located where it will become plugged by snow or other material• Must ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 26 Figure 6.2 Ceiling/Attic Construction Fire Risk • Must maintain 2 in. (51 mm) air clearance to insulation and other combustible materials. WARNING Mark the Exit Point of the Roof Locate the point where the chimney will exit the roof by plumbing dow...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 27 Termination Cap Storm Collar Slope Downward Turn-down Drip Edge Chase(Chimney) 2 in. (51 mm) Collaron Chase Top Caulk .018 (26 ga) min.GalvanizedChase Top Figure 6.3 Chase Top Construction 2 in. (51 mm) min. collar 6 in. (152mm) min. 2 in. (51 mm) ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 28 2 in. (51 mm) min. 4-1/2 in. (114 mm) max. 1-1/2 in. (38 mm) min. overlap Cap Standoff Top of Pipe Flashing Collar Figure 6.6 Installing an ST1175 or ST475 Square Termination Cap • For installations utilizing an ST1175 or ST475 Square Termination C...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 29 A. Gas Log/Lighter Provisions A certi fi ed gas log lighter or decorative gas log set can be installed in this fi replace. • Maximum input is 100,000 BTU/hr.• Decorative gas appliance must be certi fi ed to ANSI Z21.60 “Standard for Decorative Gas ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 30 8 8 Finishing A. Hearth Extension A hearth extension must be installed with all fi replaces to protect the combustible fl oor in front of the fi replace from both radiant heat and sparks. See Figures 8.1 -8.5. 2 in. (51 mm) required High temperatur...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 32 B. Finishing Material • Combustible Material Material which is made of or surfaced with wood, compressed paper, plant fi bers, plastics, or any material capable of igniting and burning, whether fl ame proofed or not, plastered or not plastered. • N...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 33 23 in. (584 mm) 50° 42 in. (1067 mm) 50-1/2 in. (1283 mm) 39° 4 in. (102 mm) BRICK FRONT FLUSH FRONT 24 in. (610 mm) 19-3/4 in. (502 mm) 24 in. (610 mm) Figure 8.8 Sidewalls/Surrounds Fire Risk Do NOT obstruct air inlets.Do NOT modify air inlets.• ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 34 9 9 Operating Instructions A. General Information Fireplaces, as well as other woodburning appliances, have been used safely for many years. It has been our experience that most problems are caused by improper installation and operation of the fi r...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 35 D. Flue Damper The fl ue damper must be in full open position, and is oper- ated by moving the handle up toward the top of the fi replace. Before lighting the fi re, verify this by looking up from the in- side of the fi replace. Always operate this...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 36 G. Grate The factory installed integral grate must be used to hold the logs from falling out of an open fi replace and to allow air to pass between the burning logs. It is important to keep the fi re off the hearth and to allow the ashes to collect...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 38 10 10 Troubleshooting Another appliance in home also exhaustingair (furnace, fan, dryer, etc.)? Air register fromfurnace nearfireplace? Doors openingand closing?Window closedfor start-up? Outside airclosed? Overhead fanoperating? Overhangingtree? B...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 39 Diagnostic Questions Possible Causes of Condition Solutions Is the damper open? • No draft Open damper. Is there enough paper/starter? • Insuf fi cient heat to ignite kindling Use more paper/starter. Is there enough kindling?Is the kindling dry? • ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 40 Diagnostic Questions Possible Causes of Condition Solutions Do you have glass doors? • Need to slow air intake Add glass doors. What is the condition of the wood? • Extremely dry wood Mix in less seasoned wood after fi re established. Diagnostic Qu...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 41 A. Disposal of Ashes Ashes should be placed in a metal container with a tight- fi t- ting lid. The closed container of ashes should be placed on a noncombustible fl oor or on the ground, well away from all combustible materials, pending fi nal disp...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 42 Fire Risk • Do not use chimney cleaners or fl ame colorants in your fi replace. Will corrode chimney. WARNING D. Maintenance Task List Asphyxiation RiskFire Risk Annual inspection by qualified technician recommended. Check: • Condition of doors, su...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 43 12 12 Reference Materials A. Fireplace Dimensions 28-1/2 in. (724 mm) 55-1/2 in. (1410 mm) (Efective Height 49-1/8 in. (1248 mm) 49-5/8 in. (1260 mm) 59-1/4 in. (1505 mm) 7-5/8 in. (194 mm) 42 in. (1067 mm) Gas Knockout 18-1/2 in. (470 mm) 8-5/8 in...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 44 B. Fireplace Components GR29 Integral Grate Bi-fold Glass Doors Traditional Brick Pattern Refractory Herringbone Pattern Refractory 20 in. (508 mm) 66 in. (1676 mm) 1/2 in. (13 mm) HX4 Hearth Extension Outside Air Shield 2 Wire Ties Flexible Duct (...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 45 C. Chimney Components The following pictures show only those chimney components which may be safely used with this fi replace. 13 in. (330 mm) 14 in. (356 mm) 14 in. (356 mm) 5-1/4 in. (133 mm) 4 in. (102 mm) CAK5A Chimney Air Kit (Required in Cana...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 46 SL1130/SL430 Offset/Return A B 17 in. (432 mm) Ceiling Firestop AS10 Straight Attic Insulation Shield 2 in. (51 mm) 13 in. (330 mm) JB577 Chimney Joint Band 13 in. (330 mm) CB576 Chimney Joint Band 39-7/8 in. (1013 mm) 28 in. (711 mm) 15-1/4in. (38...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 48 CT11-Queen CT11-Bishop CT11-Pawn CT11-Knight CT11-King 21 in. (533 mm) 47-3/4 in. (1213 mm) 24 in. (610 mm) 18-1/4 in. (464 mm) 41-1/8 in. (1045 mm) 20 in. (508 mm) 16 in. (406 mm) 38-3/8 in. (975 mm) 16 in. (406 mm) 21 in. (533 mm) 25-3/4 in. (654...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 49 Woodburning Termination Cap Shroud TS345/T445 (Top Vent) TR342/TR344TR442/TR444 TV342 TR342/TR344*TR442/TR444* (* with TR-TVK installed) TR11/TR11T TV11/TV11T TR11/TR11T* (* with TR-TVK installed) OPEN TOP with solid sides and 3 in. (76 mm) opening...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 50 D. Service Parts Service Parts List42 in. Woodburning Fireplace Service Parts ICON I80CT & I80H Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active 1 2 5 4 3 7 6 8 9 ¨

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 51 Service Parts List42 in. Woodburning Fireplace Service Parts ICON I80CT & I80H Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active # Description of Part Serial # Cutoff I80CT I80H Qty. req. 1 Damper Blade Assembly 29964 29964 1 ...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 52 This page intentionally left blank.

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 55 E. Limited Warranty HEATILATOR WOODBURNING FIREPLACE Limited Warranty As part of its 20-YEAR BUYER PROTECTION PROGRAM AS PART OF ITS 20 YEAR BUYER PROTECTION PROGRAM (“PROGRAM”), HEARTH & HOME TECHNOLOGIES INC. (“HHT”) is pleased to offer a Lim...

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08 56 Hearth & Home Technologies Inc. 1915 W. Saunders Street Mt. Pleasant, Iowa 52641 www.heatilator.com – NOTES – F. Contact Information DO NOT DISCARD THIS MANUAL CAUTION • I m p o r t a n t o p e r a t i n g a n d m a i n t e n a n c e instructio...