Heat & Glo ESCAPE-I35-C - Manuals

Page 2 - Listing Label Information/Location; Owner’s Manual; Homeowner Reference Information; NA; Read this manual before installing or operating this appliance.

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: ___________...

Page 3 - Safety Alert Key:; • NOTICE: Used to address practices not related to personal injury.; Table of Contents; User Guide

3 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. •...

Page 5 - This warranty is void if:; QRWOLPLWHGWRLPSURSHUFKLPQH\RUYHQWLQJLQVWDOODWLRQ; LIMITATIONS OF LIABILITY:; DWLRQRIJODVV

5 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 B. Limited Lifetime Warranty (continued) 4021-645C 12-29-10 Page 2 of 2 WARRANTY CONDITIONS: 7KLVZDUUDQW\RQO\FRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGWKURXJKDQ++7DXWKRUL]HGGHDOHURUGLVWULEXWRU$OLVWRI ++7DXWKRUL]HGGHDOHUVLVDYDLODEOHRQW...

Page 6 - Models; NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.; Listing and Code Approvals

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 6 C. BTU Specifi cations MODELS: ESCAPE-I30-C, ESCAPE-I30LP-C, ESCAPE-I35-C, ESCAPE-I35LP-C LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Vented Gas Appliance Heaters STANDARD: ANSI Z21.88-2009 • CSA 2.33-2009 This product...

Page 7 - Operating Instructions; A. Gas Fireplace Safety; WARNING; HOT SURFACES

7 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 2 2 Operating Instructions Figure 2.1 General Operating Parts B. Your Fireplace WARNING! DO NOT operate fi replace before read-ing and understanding operating instructions. Failure to operate fi replace according to operating ins...

Page 8 - Assembly; • Install a switch lock or a wall/remote control with child

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 8 D. Clear Space WARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth...

Page 9 - H. IPI Battery Tray/Battery Installation; The IntelliFire Plus; system has a battery backup option.; NOTCH; I. Control Module Operation; If using a wired wall switch with the module in REMOTE

9 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 H. IPI Battery Tray/Battery Installation The IntelliFire Plus TM system has a battery backup option. Battery longevity and performance will be affected by the service temperatures of this appliance. NOTICE: Batteries should only ...

Page 10 - J. Before Lighting Fireplace; MODULE RESET SWITCH; Module Reset Switch

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 10 J. Before Lighting Fireplace Before operating this fi replace for the fi rst time, have a qualifi ed technician: • Verify all shipping materials have been removed from inside and/or underneath the fi rebox. • Review proper place...

Page 11 - NOT FOR USE; Final inspection by

11 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 K. Lighting Instructions (IPI) 1. This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand. 2. Wait fi ve (5) minutes to clear out any gas. Then smell for g...

Page 12 - L. After Appliance is Lit; ISSUE

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 12 Initial Break-in Procedure • The appliance should be run three to four hours continuously on high. • Turn the appliance off and allow it to completely cool. • Remove fi xed glass assembly. See Section 12.I. • Clean fi xed glass ...

Page 13 - Glass Cleaning; Tools Needed; Maintenance and Service; Tools needed; Remote Control

13 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 Glass Cleaning Frequency: Seasonally By: Homeowner Tools Needed : Protective gloves, glass cleaner, drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scr...

Page 15 - Burner Ignition and Operation; DO NOT

15 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 Figure 3.1 IPI Pilot Flame Patterns Burner Ignition and Operation Frequency: Annually By: Service Technician Tools needed: Protective gloves, vacuum cleaner, whisk broom, fl ashlight, voltmeter, indexed drill bit set, and a mano...

Page 16 - A. Typical Appliance System; Getting Started; Installer Guide

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 16 A. Typical Appliance System NOTICE: Illustrations and photos refl ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual VERTICA...

Page 17 - Read all of the instructions before starting the instal-; C. Tools and Supplies Needed; Any such action may cause a fi re hazard.

17 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 B. Design and Installation Considerations Heat & Glo gas inserts are designed for installations into solid fuel masonry or factory built fi replaces that have been installed in accordance with the National, Provin-cial, Stat...

Page 18 - Fireplace Size Requirements; A. Minimum Fireplace Opening; RECOMMENDED

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 18 5 5 Fireplace Size Requirements A. Minimum Fireplace Opening Minimum fi replace opening requirements are shown in Figure 5.2. WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access....

Page 20 - B. Mantel and Wall Projections; • Use leveling legs to raise insert minimum 1/4 inch (6 mm)

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 20 B. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear-ances to combustibles as specifi ed. Framing or fi nishing material closer than the minimums listed must be construct-ed entirely of noncombusti...

Page 21 - A. Vent Termination Minimum Clearances; Termination Locations

21 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 A. Vent Termination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0*Over 6/12 to 7/12 .................................................1.25*Over 7/12 to 8/12 ...

Page 22 - Installation Preparation; A. Inspection and Cleaning

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 22 7 7 Installation Preparation Prepare the existing solid fuel masonry or factory built non-combustible fi rebox for installation. A. Inspection and Cleaning Prior to installing the gas insert: • Have the chimney and adjacent stru...

Page 23 - B. Venting Components; • One 3-foot section stainless steel fl exible pipe (included; Installing Vent Pipe and Appliance; • May impair safe operation of this appliance or other; Description

23 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 B. Venting Components CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal-lation. Sheet metal edges are sharp. The vertical vent termination system installed on this model inclu...

Page 24 - C. Connecting Vent Pipe

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 24 C. Connecting Vent Pipe Reference instructions in the termination kit. • Install the 3-inch fl exible vent pipe(s) down through the chimney. • Secure the exhaust fl exible vent pipe to the 3 foot section stainless steel flexible...

Page 25 - Placing, Securing and Leveling the; • The 3 foot section of stainless steel fl exible pipe MUST

25 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 WARNING! Risk of Fire! Only an approved Hearth & Home Technologies surround may be used to cover inte-gral grills on solid fuel burning fi replaces. No other com-ponents such as shrouds, sheetmetal plates, etc., may be used ...

Page 26 - E. Installing Adaptor and Termination Cap; Masonry; OR; Note

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 26 E. Installing Adaptor and Termination Cap CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal-lation. Sheet metal edges are sharp. For installation of termination cap see minimu...

Page 27 - • Purge should be performed by technician certifi ed by; Gas Information; • If substituting for these components, please consult; D. High Altitude Installations; Gas Pressure

27 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualifi ed technician (NFI certifi ed or factory-trained) using Hearth & Home Technologies specifi ed and a...

Page 28 - A. Wiring Requirements; Electrical Information; Ignition System Wiring

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 28 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Elec...

Page 29 - D. Control Module Operation

29 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 E. Optional Accessories To connect optional accessories, the supplied cord as-sembly should be used. See Figures 10.2 and 10.3 for optional accessories. WARNING! Risk of Shock! Label all wires prior to dis-connection when servic...

Page 30 - NOTE: SEE FIGURE 10.1 FOR ADDITIONAL INFORMATION; G. Programming the RC300 to the Control; • Refer to the RC300 Installation Instructions included

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 30 Figure 10.3 Fan Wiring Diagram Note: if any of the original wire as supplied with the appliance must be replaced, it must be replaced with type 105 °C rated wire. BLK RED BRN ORANGE - TO VALVEGROUND - TO VALVE BRACKET GREEN - TO...

Page 31 - A. Mantel and Wall Projections; Finishing

31 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 A. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear-ances to combustibles as specifi ed. Framing or fi nishing material closer than the minimums listed must be construct-ed entirely of noncombusti...

Page 32 - Appliance Setup

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 32 A. Remove Glass Assembly See Section 12.I. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. Remove metal panels covering electrical compo-nents on sides of appliance. C. Inspect ...

Page 34 - H. Install the Log Assembly; BURNER LEDGE

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 34 H. Install the Log Assembly Log Set Assembly: LOGS-I30FBModels: ESCAPE-I30-C, ESCAPE-I30FB CAUTION: Logs are fragile, handle with care. Figure 1. Log Set Installed Figure 2. Reference Points PILOT PILOT BRACKET BRACKET GRATE TIN...

Page 37 - LIGHT TRAYS

37 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 H. Install the Log Assembly Log Set Assembly: LOGS-I35FB Models: ESCAPE-I35FB, ESCAPE-I35FB-LP ESCAPE-I35-C, ESCAPE-I35LP-C CAUTION: Logs are fragile, handle with care. Figure 1. Log Set Installed Figure 2. Reference Points PILO...

Page 40 - J. Air Shutter Setting; Glass; Removing Fixed Glass Assembly; • The glass assembly fastens to the fi replace in four; Replacing Fixed Glass Assembly; • Tilt glass assembly toward fi replace and slide glass; Air Shutter Settings; NG

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 40 J. Air Shutter Setting Air shutter settings should be adjusted by a qualifi ed ser-vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer v...

Page 41 - Troubleshooting; A. IntelliFire PlusTM Ignition System; Symptom

41 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 13 13 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualifi ed techni...

Page 43 - Reference Materials; A. Appliance Dimension Diagram

43 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 14 14 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Figure 14.1 Appliance Dimensions A B C D E F H L M R S H O Q P N K J I MODEL DIMENSIONS Location Escape...

Page 44 - B. Vent Kits Components

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 44 B. Vent Kits Components Direct Vent Flex Liner Kits (see Figure 14.2) LINK-DV30B: Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter. LINK-DV4-30B: Masonry 3 in...

Page 45 - 0” FireBrick Insert; Log Set Assembly

45 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 C. Service Parts ESCAPE-I30-C Beginning Manufacturing Date: Aug 2011 Ending Manufacturing Date: ______ 30” FireBrick Insert Log Set Assembly IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for ...

Page 47 - Beginning Manufacturing Date: Aug 2011; Stocked; ITEM

47 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 C. Service Parts ESCAPE-I30-C, ESCAPE-I35-C Beginning Manufacturing Date: Aug 2011 Ending Manufacturing Date: ______ #15 Valve Assembly 14.2 14.3 14.4 14.6 14.5 14.7 14.8 14.9 14.10 14.11 14.12 14.13 14.14 14.15 14.16 14.17 14.1...

Page 49 - D. Contact Information; For the location of your nearest Heat & Glo dealer,; DO NOT DISCARD THIS MANUAL; NOTICE

49 Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12 Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www.heatnglo.com D. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For th...