Heat & Glo AT-GRAND-D - Manuals

Page 2 - Owners Guide; SAFETY AND WARNING; Installers; CONSIGNES DE SÉCURITÉ

2 READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the Owners Guide ...

Page 4 - Section 4: Maintaining and Servicing; Table of Contents; Consignes de sécurité; Table des matières

4 Safety and Warning Information ............................... 2 Service Parts List ........................................................ 5 Section 1: Approvals and Codes ............................... 7 Approval Listing and Codes ............................................ 7Appliance Certifi...

Page 5 - La liste des numéros de pièce se trouve à la page suivante.; Log Set Assembly; Service Parts

5 AT-GRAND-D (NG, LP) Exploded Parts Diagram / AT-GRAND-D (GN, PL) Vue éclatée des pièces * Part number list on following page.* La liste des numéros de pièce se trouve à la page suivante. 3 4 6 Log Set Assembly 7 2 5 1 8 9 10 13 12 11 14 Service Parts

Page 6 - AC C E S S OR IE S / AC C E S S OIR E S; supply serial and model numbers to ensure correct service parts. /

6 IT E M / P IÈ C E S TAN D IN G P IL OT / V E IL L E U S E S E R IAL # / N° DE SÉRIE PAR T N U MB E R / N ° D E P IÈ C E ON/OFF Rocker S witch / Interrupteur à bascule marche/arrêt 0 6 0 -5 2 5 A P i e zo Ig ni to r / A llum a g e P i é zo 4 1 8 -5 1 3 B urne r Tub e / Tub e d e b rûle ur 4 7 7 -3 ...

Page 7 - Installers Guide; Approvals and Codes; Guide

7 Appliance Certification The Heat-N-Glo models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. CERTIFICATION STANDARD MODEL AT-Grand-D LABORATORY Underwriters Laboratories TYPE Direct Vent Gas Fireplace Heater STANDARD ANSI Z...

Page 8 - High Altitude Installations; Installations à haute altitude; Homologations et codes

8 High Altitude Installations U.L. Listed gas appliances are tested and approved for elevations from 0 to 2,000 feet in the U. S. A. and are tested and approved for elevations from 0 to 4,500 feet in Canada. When installing this appliance at an elevation above 2,000 feet (in the United States), it m...

Page 10 - Guide dinstallation; Getting Started

10 VENTING AND INSTALLATION 1. Heat-N-Glo gas inserts are designed for recessed instal- lations into solid fuel Masonry or Factory Built Non Com- bustible fireplaces that have been installed in accordance with the National, Provincial, State and local building codes. 2. Minimum appliance opening req...

Page 11 - When planning a fireplace insert installation, its necessary; Mise en marche

11 Figure 1. Schéma du modèle AT-GRAND-D Figure 1. Diagram of the AT-GRAND-D Getting Started (continued) When planning a fireplace insert installation, its necessary to determine: The vent system configuration to be used. Gas supply piping. Whether optional accessoriesdevices such as a wall ...

Page 14 - Installing the Insert; Figure 2. Minimum Height from Roof to Lowest; ROOF PITCH; Figure 2. Hauteur minimum du toit à lorifice; Installation; Pente du toit

14 WARNING: MAJOR U.S. BUILDING CODES SPECIFY MINIMUM CHIMNEY AND/OR VENT HEIGHT ABOVE THE ROOF TOP. THESE MINIMUM HEIGHTS ARE NECESSARY IN THE INTEREST OF SAFETY. SEE THE FOLLOWING DIAGRAM FOR MINIMUM HEIGHTS, PROVIDED THE TERMINATION CAP IS AT LEAST 2-FEET FROM A VERTICAL WALL AND 2-FEET BELOW A H...

Page 16 - Figure 4

16 Installing the Insert (continued) Installation (suite) Figure 4 Figure 5 INLET AIR STARTING COLLAR (COLLIER DE DÉPART D’ADMISSION D’AIR) EXHAUST STARTING COLLAR (COLLIER DE DÉPART D’ÉCHAPPEMENT) TERMINATION CAP (MITRE) ADAPTOR (ADAPTATEUR) INLET AIR COLLAR (COLLIER D’ADMISSION D’AIR) EXHAUST COLL...

Page 23 - Glass Assembly

23 Installing the Insert (continued) 1. Place the ember material onto the top of the burner. 1. Lift the top trim door up and out of the unit. 2. Unlatch and remove the glass door from the unit. Figure 10. Glass Assembly Figure 11. Placement of the Ember Material 1. Soulever lencadrement de la port...

Page 27 - Appliance Maintenance; IMPORTANT: TURN OFF THE GAS BEFORE SERVICING; Entretien et révision; Entretien; IMPORTANT: COUPER LALIMENTATION EN GAZ

27 Maintaining and Servicing Your Appliance 4 Appliance Maintenance Although the frequency of servicing and maintenance will depend on use and the type of installation, you should have a qualified service technician perform an appliance check- up at the beginning of each heating season. Specific gui...

Page 28 - tions or concerns. For the number of your nearest Heat-; Contacter le concessionnaire Heat-N-Glo pour toute

28 Checking Vent System Frequency: Before initial use and at least annually thereafter, more frequently if possible. By: Qualified service technician/Home owner. Task: Inspect the external vent cap on a regular basis to ensure that no debris is interfering with the flow of air. Inspect entire vent s...