Heat & Glo 550TRSI-AUF - Manuals

Page 2 - the glass door; PLEASE READ THIS MANUAL BEFORE INSTALLING; before leaving the installation site.

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 2 MODELS: 550TRSI-AUF, 550TRSILP-AUF ARE SAI GLOBAL APPROVED FOR NATURAL GAS, PROPANE OR BUTANE AS A BALANCED FLUE HEATER. Refer to the appliance data plates for gas consumptions and pressures.Installation of this appliance should ...

Page 3 - Homeowner Reference Information; Read this manual before installing or operating this appliance.; Listing Label Information/Location; SAMPLE

3 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fireplace: _____________________ Dealership purchased from...

Page 4 - FOR YOUR SAFETY; GAS-PRESSURE REGULATOR; Novida Testing Service; Safe Appliance

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 4 FOR YOUR SAFETY This appliance is designed to operate on LPG IF YOU SMELL GAS: • Turn off as supply at bottle• Extinguish all naked fl ames• Do not operate any electrical appliances• Ventilate the area• Check for leaks as detaile...

Page 5 - Safety Alert Key:; Indicates a hazardous situation which, if not avoided will; Table of Contents; User Guide; Appliance Preparation

5 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. •...

Page 7 - C. Limited Lifetime Warranty; AUSTRALIAN WARRANTY INFORMATION; ill; All Parts and Material Except

7 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 C. Limited Lifetime Warranty AUSTRALIAN WARRANTY INFORMATION Warranty information in the attached manual is for international markets, not Australia. For Australian warranty information, please see below. Hearth & Home Techno...

Page 8 - OTHER RIGHTS; tions or

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 8 Warranty Period Heat & Glo Manufactured Appliances and Venting Components Covered Parts Labor Gas Wood Pellet EPA Wood Coal Electric Venting 5 years 1 years X X Castings & baffl es 7 years 3 years X X X Manifold tubs HEAT...

Page 9 - charges for parts; This warranty is void if:; ring can be identi; HOW TO CLAIM; you originally purchased the product.; Melbourne; Perth; Fireplace Corner; Sydney; Jetmaster

9 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 • Non Heat & Glo venting components, hearth components or other accessories used in conjunction with the appliance. • Any part of a pre-existing fi replace system in which an insert or a decorative gas appliance is installed....

Page 10 - A. Appliance Certification; Listing and Code Approvals; SAI Global; C. High Altitude Installations; If the heating value of the gas has been reduced,; D. Non-Combustible Materials Specification; Standard Test Method for Behavior of Materials in a; and; E. Combustible Materials Specification; The Heat & Glo gas appliances discussed in this Installer’s; B. Gas Pressure Requirements; An in-line regulator; Natural Gas

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 10 A. Appliance Certification 1 Listing and Code Approvals MODELS: 550TRSI-AUF, 550TRSILP-AUF LABORATORY: SAI Global TYPE: Gas Space Heating Appliance STANDARD: AS4553-2008 C. High Altitude Installations NOTICE: If the heating valu...

Page 11 - WARNING! DO NOT operate fireplace before read-; A. Gas Fireplace Safety; WARNING; This appliance has been supplied with an integral barrier; HOT SURFACES; touch glass until it is cooled; High temperatures may ignite clothing or other; Operating Instructions

11 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Figure 2.1 General Operating Parts B. Your Fireplace WARNING! DO NOT operate fireplace before read- ing and understanding operating instructions. Failure to operate fireplace according to operating instructions could cause fire ...

Page 12 - F. Fixed Glass Assembly; Install ONLY doors or fronts; G. Remote Controls, Wall Controls and Wall; H. Before Lighting Fireplace; have a; WARNING! Risk of Fire or Asphyxiation! DO NOT

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 12 D. Clear Space WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth....

Page 13 - NOT FOR USE; try to light the burner by; WHAT TO DO IF YOU SMELL GAS; DO NOT CONNECT LINE VOLT-; operate the appliance with; Also Certified for Installation in a; Final inspection by

13 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 I. Lighting Instructions (IPI) 1. This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand. 2. Wait five (5) minutes to clear out any gas. Then smell for ga...

Page 14 - J. Control Module Operation; initial installation or power outage operation with battery; Nine Hour Safety Shutdown Feature

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 14 Note: If the module is in LOCK-OUT mode, resetting the circuit breaker to the appliance will also reset the module. Note: For units installed in Australia, the residence’s 220/240 wall outlet to which this appliance’s power cord...

Page 15 - K. After Fireplace is Lit; continuously on high.; L. Frequently Asked Questions; ISSUE

15 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 K. After Fireplace is Lit Initial Break-in Procedure• The fireplace should be run three to four hours continuously on high. • Turn the fireplace off and allow it to completely cool.• Remove fixed glass assembly. See Section 9.E....

Page 16 - Glass Cleaning; Tools Needed; CAUTION! Handle fixed glass assembly with care.; Note; cleaner; Maintenance and Service; CAUTION! Risk of Burns! The fireplace should be turned; Tools needed; Remote Control; Any safety screen or guard removed for servicing must be

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 16 Glass Cleaning Frequency: Seasonally By: Homeowner Tools Needed : Protective gloves, glass cleaner, drop cloth and a stable work surface. CAUTION! Handle fixed glass assembly with care. Glass is breakable. • Avoid striking, scra...

Page 17 - cloths; DO NOT

17 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 B. Maintenance Tasks-Qualified Service Technician The following tasks must be performed by a qualified ser- vice technician. Gasket Seal and Glass Assembly Inspection Frequency: Annually By: Qualified Service Technician Tools ne...

Page 18 - A. Typical Appliance System; drawn to scale. Actual product may vary from pictures in manual; Dual venting c onf igurations; ARE NOT; allowed. Appliance; MUST; b e ve nte d; E I T H E R; ve r t i c a l l y; O R; Getting Started; Installer Guide

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 18 A. Typical Appliance System NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Figure 4...

Page 19 - Read all of the instructions before starting the instal; Damaged parts; C. Tools and Supplies Needed; Hearth & Home Technologies disclaims any responsibility for,; Any such action may cause a fire hazard.; DO NOT; Improper installation, adjustment, alteration, service or

19 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 B. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside of the bui...

Page 20 - Framing and Clearances; A. Selecting Appliance Location; When selecting a location for the appliance it is important to

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 20 5 Framing and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). WARNING! Risk of Fire or Burns! Provide adequate...

Page 21 - B. Constructing the Appliance Chase; NOTICE: Treatment of ceiling firestops and wall shield; Not intended for heater insert.

21 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase. NOTICE: Treatment of ceilin...

Page 23 - D. Mantel and Wall Projections; WARNING! Risk of Fire! Comply with all minimum clear; Combustible Mantels; All measurements in millimeters.; If joints between the finished walls and the heater surround; Zero clearance finishing allowed on sides of surround

23 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 D. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear - ances as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncom- bustible materials (...

Page 24 - A. Vent Termination Minimum Clearances; Termination Locations; pack air space with insulation or other

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 24 A. Vent Termination Minimum Clearances Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening 6 Termination Locations Fire Risk.Maintain vent clearance to combustibles as specified.• DO NOT pack air space with insulatio...

Page 25 - MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS; below

25 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Figure 6.3 Minimum Clearances for Termination NOTES: 1. All distances are measured vertically or horizontally along the wall to a point in line with the nearest part of the terminal. 2. Prohibited area below electricity meter or...

Page 26 - WARNING! Risk of Fire or Asphyxiation.; Vent Information and Diagrams; D. Measuring Standards

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 26 A. Approved Pipe This appliance is approved for use with Hearth & Home Technologies DVP and SLP venting systems. Refer to Section 16.B for vent component information. DO NOT mix pipe, fittings or joining methods from differ-...

Page 27 - Top Vent - Horizontal Termination; USE SLP SERIES COMPONENTS ONLY; Minimum

27 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Example: DVP pipe 3 ft. (1 m) min. vertical = 11 ft. (3.35 m) max. horizontal SLP pipe 7 ft. (2.13 m) min. vertical = 11 ft. (3.35 m) max. horizontal Figure 7.4 Top Vent - Horizontal Termination Fire Risk. Explosion Risk.Do NOT ...

Page 28 - Two Elbows; INSTALLED; Elbow only

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 28 Top Vent - Horizontal Termination - (continued) Figure 7.5 Two Elbows INSTALLED HORIZONTALLY H 1 H 2 V 1 V 1 Minimum H 1 + H 2 Maximum Elbow only Not allowed 6 in. 152 mm 1 ft. 305 mm 1 ft. 305 mm 2 ft. 610 mm 2 ft. 610 mm 4 ft....

Page 29 - Three Elbows; must be attached to the heater before a 90° elbow.

29 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Figure 7.6 Three Elbows H 2 H 1 V 2 V 1 Note: A 6 in. (152 mm) section of straight flue must be attached to the heater before a 90° elbow. USE SLP SERIES COMPONENTS ONLY V 1 Min. H 1 Max. V 2 Min. H 2 Max. 6 in. 152 mm 1 ft. 305...

Page 30 - Top Vent - Vertical Termination; NO OTHER FLUE SYSTEMS OR COMPONENTS; This gas appliance; Straight Up Vertical Flue System; MODEL

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 30 Top Vent - Vertical Termination This model is approved to use DVP-Series flue pipe com- ponents. A DVP-TVHW vertical Termination Cap must be used to terminate flue systems in a vertical position.Approved flue system components a...

Page 31 - Flue System Approvals And Installations; manual; SLP SERIES

31 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 MODEL 550TRSI-AUF 550TRSILP-AUF FLUE TERMINATION APPROVALS DVP-TRAP2 HORIZONTAL TERMINATION CAP DVP-FBHT HORIZONTAL TERMINATION CAP DVP-TVHW VERTICAL TERMINATION CAP Flue System Approvals And Installations These models have flue...

Page 32 - Maximum

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 32 Figure 7.10 H 1 V 1 V 2 USE SLP SERIES COMPONENTS ONLY Two Elbows Top Vent - Vertical Termination - (continued) V 1 H 1 Maximum V 2 V 1 + V 2 Min. Elbow only Not allowed * * * 6 in. 152 mm 2 ft. 610 mm * * * 1 ft. 305 mm 4 ft. 1...

Page 34 - Do not use a 45o elbow in corner installations.; USE DVP SERIES COMPONENTS ONLY

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 34 Rear Vent - Horizontal Termination Figure 7.13 No Elbow One 45º Elbow H 1 Do not use a 45º elbow in corner installations. Use two 90º elbows instead. Figure 7.12 USE DVP SERIES COMPONENTS ONLY USE DVP SERIES COMPONENTS ONLY H 1 ...

Page 36 - m; Back to Back 90o Elbows

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 36 Rear Vent - Vertical Termination One Elbow Figure 7.16 Two Elbows Figure 7.17 V 1 H 1 INSTALLED HORIZONTALLY H 1 H 2 V 1 USE DVP SERIES COMPONENTS ONLY USE DVP SERIES COMPONENTS ONLY V 1 Minimum H 1 Maximum 1 ft. 305 mm 3 ft. 91...

Page 37 - *No specific restrictions on this value EXCEPT

37 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Rear Vent - Vertical Termination - (continued) Three Elbows Figure 7.17 Three Elbows Figure 7.18 INSTALLED HORIZONTALLY H 3 H 1 H 2 V 1 V 2 V 1 H 2 H 1 USE DVP SERIES COMPONENTS ONLY USE DVP SERIES COMPONENTS ONLY H 1 H 2 H 3 V ...

Page 38 - A. Pipe Clearances to Combustibles; Maintain air space clearance to; Vent Clearances and Framing; B. Wall Penetration Framing; Combustible Wall Penetration; be attached to the fireplace before a 90° elbow.

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 38 A. Pipe Clearances to Combustibles WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling firestops • Between wall shield firestops • Around vent systemFailur...

Page 39 - C. Install the Ceiling Firestop; be used between; DVP pipe only; lation around the vent. Insulation must be kept

39 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 C. Install the Ceiling Firestop A ceiling firestop MUST be used between floors and attics.• DVP pipe only - Frame an opening 10 in. x 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.3). • SLP...

Page 40 - Kit; Vaulted Ceiling Installation; D. Install Attic Insulation Shield; allow loose materials or; Flat Ceiling Installation; NOTICE: Cut previously installed batt insulation to make

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 40 Figure 8.5 Attic Insulation Shield Figure 8.6 Heat Zone ® Knockout E. Installing the Optional Heat-Zone ® -240V Kit • Remove the knockout from the fireplace and discard it (see Figure 8.6). • Center the duct collar around the ex...

Page 41 - Appliance Preparation; : Actual unit may look different than the fireplace shown; evated header temperatures may cause a fire.

41 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp.NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a ...

Page 43 - D. Securing and Leveling the Appliance; • Sagging or loose insulation; HEADER

43 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Figure 9.16 Proper Positioning and Securing of an Appliance NAILING TABS (BOTH SIDES) PILOT HOLES Figure 9.14 Non-combustible Board C. Installing the Non-combustible Board The factory supplied non-combustible board must be used....

Page 44 - E. Covers Removal For Servicing; Control Compartment Access Door; G. Parts Replacement; Fan; H. Adjustments And Replacement Parts; NOTICE: All screws which were removed must be replaced.; Fixed Glass Assembly; WARNING! Risk of Asphyxiation! Handle fixed glass; Removing Fixed Glass Assembly

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 44 Natural Gas Propane Butane 550TRSI-AUF 11.13 mm N/A N/A 550TRSILP-AUF N/A Full Open Full Open Figure 9.17 Fixed Glass Assembly GLASS ASSEMBLY LATCHES (BOTH BOTTOM AND TOP) E. Covers Removal For Servicing Control Compartment Acce...

Page 45 - Attach Vent to the Firebox Assembly; The end of the pipe sections with the lanced tabs will face; Assemble Pipe Sections; penetrate; Make sure that the seams are not aligned to prevent; INCORRECT; Lances

45 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 10 Installing Vent Pipe (DVP and SLP Pipe) A. Assemble Vent Sections (DVP Pipe Only) Attach Vent to the Firebox Assembly Note: The end of the pipe sections with the lanced tabs will face toward the appliance. Attach the first pi...

Page 46 - including the slip section that connects directly to the hori; WARNING! Risk of Fire or Explosion! DO NOT break; then rotate counterclockwise to lock; C. Assemble Slip Sections; Pilot hole; NOTICE: When installing a vent system with an HRC

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 46 B. Assemble Vent Sections (SLP Pipe Only) To attach the first vent component to the starting collars of the appliance:• Lock the vent components into place by sliding the pipe section onto the collar. • Align the seam of the pip...

Page 47 - E. Disassemble Vent Sections; Improper support may allow vent to sag and separate.

47 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 120º Figure 10.8 Securing Vertical Pipe Sections 120º Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble Vent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown ...

Page 48 - REQUIRED; at the hole; G. Install Firestops; on both; MUST BE; placed; F. Install Support Brackets; For Horizontal Runs -

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 48 10 in. (254 mm) 12 in. (305 mm) INTERIOR WALL SHIELD Figure 10.13 Flue Pipe & Firestop Figure 10.14 Hole and New Framing Members For Vertical Runs - One firestop is REQUIRED at the hole in each ceiling through which the flue...

Page 49 - IS; the termination cap must be; For Horizontal Terminations using the SLP-TRAP2 or; Cap Specification Chart

49 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Figure 10.15 Ceiling Firestop (Ceiling Side) Figure 10.16 Attic Firestop CEILING CEILING FIRESTOP RAFTER NAILS (4 REQUIRED) JOIST CEILING FIRESTOP CEILING NAILS (4 REQUIRED) If the area above the ceiling IS an attic, position an...

Page 50 - J. Install Metal Roof Flashing; NOTICE: Failure to properly caulk the roof flashing could; Heat shields may; I. Heat Shield Requirements for Horizontal; heat shields must extend through the entire wall thick

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 50 J. Install Metal Roof Flashing • See minimum vent heights for various pitched roofs (Figure 10.19) to determine the length of pipe to extend through the roof. • Slide the roof flashing over the pipe sections extending through th...

Page 51 - CAULK; K. Assemble and Install Storm Collar; Wear protective gloves and safety glasses during instal-; L. Install Vertical Termination Cap; MUST BE; BRACKETS

51 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 CAULK K. Assemble and Install Storm Collar CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. • Connect both halves of the storm colla...

Page 52 - Gas Information; A. Gas Pressure Requirements; pressure testing gas line at test pressures

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 52 11 Gas Information A. Gas Pressure Requirements WARNING! Risk of Explosion! An in-line regulator MUST be installed if the gas pressure exceeds 3.7 kPa. Failure to install a regulator could damage valve. Pressure requirements for...

Page 54 - Electrical Information; A. Wiring Requirements; NOTICE: This appliance must be installed by a qualified; B. IntelliFire PlusTM Ignition System Wiring; WARNING! Risk of Shock or Explosion! DO NOT; C. Optional Accessories Requirements; Optional Remote Control Receiver Location

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 54 12 Electrical Information A. Wiring Requirements NOTICE: This appliance must be installed by a qualified electrician in accordance with the relevant national and local regulations. • Wire the appliance junction cord to 220-240 V...

Page 55 - E. Control Module Operation

55 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 BLUE BROWN GREEN/ YELLOW Figure 12.2 D. Blower These heaters have a factory installed fan and electrical junction cord. These components are located behind the lower door.Use of the fan requires that the Junction cord (factory i...

Page 56 - • Read, understand and follow these instructions for safe; Introduction

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 56 Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:• Installation and use of any damaged system component.• Modification of the system component.• Installat...

Page 57 - Installation of Remote Control Housing; install damaged or; Changing Temperature Scale; FCC Requirements; WARNING! Risk of Fire! Changes or modifications to

57 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 5. Close the housing door. See Figure 12.7. 4. Place remote control inside housing. See Figure 12.6. Figure 12.6 Remote in Housing Installation of Remote Control Housing CAUTION! Risk of Fire! DO NOT install damaged or modified ...

Page 58 - AUX300CE Module Installation; CONTROL MODULE; FAN CORD; Programming the RC300AU to the Control Module; DO NOT program the remote; press any buttons on the

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 58 Figure 12.7 Mounting Remote Control Housing AUX300CE Module Installation • Insert the 4 hole harness from the AUX300CE module into the 4 pin plug on the control module. See Figure 12.8. Fan Installation • Insert the 3 prong plug...

Page 59 - Function Buttons; For example: Flame Height will not; Idle When Remote is in ON Mode

59 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 FIREPLACE STATUS THERMOSTAT THERMOSTAT DESIRED TEMP SETTING FLAME HEIGHT FAN SPEED ADJUSTABLE AUXILIARY ADJUSTABLE OUTPUT (ON/OFF) TIMER DISPLAY/FUNCTION ROOM TEMP DISPLAY FUNCTION LEVEL INDICATOR LOW BATTERY INDICATOR TRANSMISS...

Page 60 - NOTICE: Whenever the fireplace is cycled from OFF to; Adjusting Flame Height; NOTICE: FLAME HEIGHT will not be adjustable for first; Adjusting Fan Speed; NOTICE: The fan has a timer built into the control module.

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 60 About ON Mode • All functions can be accessed when the remote control is in the ON mode. • Only active functions will be displayed when the remote control is in the ON mode. For example: if the fan is the only function that’s ac...

Page 61 - Adjusting Thermostat; NOTICE: If the THERMO function is on, the SET TEMP; Adjusting Timer; NOTICE: No functions will be usable until child lock feature; Power Outage; NOTICE: Battery polarity must be correct or module; Manual Fireplace Shutoff; Fireplace surfaces are hot

61 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Adjusting Thermostat • Press the MENU button to activate the menu. • Using the UP and DOWN arrows highlight the THERMO icon and press SELECT . • Use the UP and DOWN arrows to turn the THERMO ON or OFF , then press SELECT (the SE...

Page 62 - Frequently Asked Questions/Troubleshooting; Symptom; to each other

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 62 Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action Remote control will not transmit Batteries Verify batteries are functional and installed correctly. Remote control is in Child Lock mode Disenga...

Page 63 - Finishing; A. Mantel and Wall Projections; apply combustible; Inches; TOP VIEW

63 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 13 Finishing A. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear - ances as specified. Framing closer than the minimums list - ed must be constructed entirely of noncombustible materials (i.e., st...

Page 64 - Remove shipping materials from inside or underneath the; C. Clean the Appliance; Clean/vacuum any sawdust that may have accumulated; Appliance Setup

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 64 A. Remove Fixed Glass Assembly See Section 9.E. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the firebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside t...

Page 65 - E. Log Placement Instructions; Logs are fragile! Carefully remove the logs from the packaging.

65 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 E. Log Placement Instructions Log Assembly: LOGS-550TRSAUD CAUTION: Logs are fragile! Carefully remove the logs from the packaging. LOG #2 (SRV347-703): Place log #2 so that its left edge sits against the left front grate corner...

Page 66 - back to the locating tab as the grate tine.

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 66 LOG #4 (SRV278-705): Position log #4 between log #1 and the locating tab on the fourth grate tine. Push its left hand side back to the locating tab as the grate tine. 4 4 5 5 LOG #3 (SRV349-704): Position log #3 so that its righ...

Page 67 - Place log #6 on the base on front of the grate as shown.

67 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 LOG #7 (SRV484-703): Place log #7 on the groove in log #2 with its rear top on log #1 and front top resting on log #5. LOG #8 (SRV347-701): Hook log #8 on the right hand corner grate tine and rest its rear on log #1 as shown. 7 ...

Page 68 - Troubleshooting; A. IntelliFire PlusTM Ignition System; there is no noise or

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 68 15 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service te...

Page 69 - sensing rod

69 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Troubleshooting (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but contin- ues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot flame has been lit, flame rectifica...

Page 70 - Reference Materials; A. Appliance Dimension Diagram; Location

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 70 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. Figure 16.1 Appliance Dimensions Location Inches...

Page 71 - B. Maintenance Tasks; Inspect

71 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 B. Maintenance Tasks Inspect Maintenance Tasks Doors 1. Inspect for scratches, dents or other damage and repair as necessary.2. Verify no obstructions to airflow.3. Verify maintenance of proper clearance to combustible household...

Page 72 - C. Vent Components Diagrams

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 72 C. Vent Components Diagrams Figure 16.3 DVP vent components Pipe Effective Length Inches Millimeters DVP4 4 102 DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152 DVP12A 3 to 12 76 to 305 DVP1...

Page 73 - continued

73 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 C. Vent Components Diagrams ( continued ) Figure 16.4 DVP vent components DVP-TRAP2 DVP-TRAP2 Horizontal Termination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST overlap by ...

Page 74 - SS termination caps on top vented

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 74 DVP-TRAPFL Flashing DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination Cap Fire Risk. • When using DVP-HRC-SS and DVP-HRC-ZC- SS termination caps on top vented ﬁreplaces, a 6 inch (152 mm) minimum vert ical vent section is require ...

Page 75 - B. Vent Components Diagrams

75 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 B. Vent Components Diagrams (continued) Figure 16.6 SLP Series Vent Components 8-3/4 in. 222 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 6 in. 152 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 9-7/8 in. 251 mm 6-1/2 in. 165 mm 9-1/4 in. 235 mm ...

Page 77 - Log Set Assembly; ITEM

77 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 D. Service Parts Beginning M anufacturing Date: July 2010 Ending M anufacturing Date: ______ 550TRSI-AUF, 550TRSILP-AUF Log Set Assembly IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your...

Page 78 - Service Parts; Beginning

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 78 Service Parts Beginning M anufacturing Date: July 2010 Ending M anufacturing Date: ______ 550TRSI-AUF, 550TRSILP-AUF #19 Valve Assembly IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your ...

Page 79 - Service Parts List; Conversion Kits

79 Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 Service Parts List 550TRSI-AUF, 550TRSILP-AUF IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual m...

Page 80 - E. Contact Information; For the location of your nearest Heat & Glo dealer,; DO NOT DISCARD THIS MANUAL; NOTICE

Heat & Glo • 550TRSI-AUF, 550TRSILP-AUF • 2079-980 Rev. N • 5/12 80 E. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, please visit www.heatnglo.com. - NOTES - __________________________________...