Hand Held Products IT4710 - Manuals

1 - 1 1 Introduction Two-dimensional Print Quality Assessment (2D PQA), a feature of HHP's image readers, identifies a successfully read symbol and also reports graded mea-surement parameters obtained from the symbol. 2D PQA is not "true" verification in the traditional sense of the word; ho...

1 - 2 • The hand-held imager has a view finder that projects a bright aiming beam that corresponds to the imager’s horizontal field of view. The aiming beam should be centered over the bar code and positioned horizontally over the code (no tilt, skew, or rotation). If the symbol surface is shiny, th...

1 - 3 2D PQA Reporting Full Report HHP's 2D PQA reporting can be enabled in two different modes: Full Report or Screening. If you are using Quick*View, you can enable Full Report, a listing of all of a sym-bol's identifying information, measurements, and corresponding grades, by typ-ing the followin...

1 - 4 If your imager is in keyboard wedge mode, enable Screening by scanning the following bar codes. You can exit both Full Report and Screening modes by either typing the menu command, 2D_PQA0, if you are using Quick*View, or by scanning the following bar code: Identifying Symbol Content To identi...

1 - 6 {5} [A] < Row Height = 3.1 X {6} [A] < Useful Row Height = 2.5 X (82% Row) {7} [A] < Data Safety Margin = 100% (0 Erasures & 0 Errors) {8} [B] < Edge Accuracy = 59% {9} [C] < Print Growth = -43% of X where: {1} is always the Encoded Message, the usual data output. In this ca...

1 - 7 D if Useful Height >= 1.0 X, else F otherwise In Screening modes, this parameter is reported as "Useful Row Height is Too Short (1.5X)" when that is the case. {7} lists the Data Safety Margin , which is the ratio of the unused error correc- tion words to the recommended (!) number o...

1 - 8 In rare instances where neither a valid Start nor Stop pattern is measurable, yet the symbol is somehow read, lines {8} and {9} are replaced by a message to that effect. The message is either: "[F] < Start/Stop Decode Fails" in a Full Report or "Start/Stop Characters are Bad"...

1 - 9 A if Row Height >= 1.5 X, F otherwise. {6} lists the Data Safety Margin . Because MicroPDF's error correction level is fixed, this parameter is just the "Unused Error Correction" and always between 0 and 100%. {7} lists the Edge Accuracy measured in multiple scans through the Row Ad...

1 - 10 Note: The reported X-dimension is approximate and based upon use of the IT4410LR at 4.7 in (12 cm) (see "Reading Techniques" on page 1-1). If you use different image engines, the X-dimension will vary. If you hold the reader closer than 4.7 in (12 cm), it will have the effect of repor...

1 - 11 {7} [A] < Data Safety Margin = 100% {8} [A] < Horizontal Print Growth = +10% of X {9} [A] < Vertical Print Growth = +12% of X {1} is the Encoded Message . {2} is the Banner heading. {3} identifies the Symbology (DATA MATRIX) and lists the symbol's ECC and size. {4} lists the numbers ...

1 - 12 {3} QR CODE: Model 2 Version 3 (29 x 29 modules) {4} Mask Pattern Reference #3, Error Correction Level "M" {5} Data Field: 44 data & 26 checks in 1 block(s) of GF(256) {6} X roughly = 0.025" {7} [A] < Data Safety Margin = 100% {8} [A] < Horizontal Print Growth = +20% of ...

1 - 13 {4} X roughly = 0.043" {5} [A] < Data Safety Margin = 100% {6} [A] < Horizontal Print Growth = +2% of X {7} [A] < Vertical Print Growth = -1% of X {1} is the Encoded Message . {2} is the Banner heading. {3} identifies the Symbology (MAXICODE) and lists the symbol's Mode. {4} pres...

1 - 14 {7} [A] (Ok) < Bar Widths = 0.022 in. {8} [A] (Ok) < Inter-Bar Gaps = 0.023 in. {1} is the Encoded Message . {2} is the Banner heading. {3} identifies the Symbology , (POSTNET or PLANET Code), and lists also the symbol's size and allowed range of measured width. {4} lists the Bar Sequen...

1 - 16 Note: For the Canadian and Australian 4-State symbologies only, any bar error that has invoked their error correction triggers an additional PQA parameter line: "[F] < One or more Bars are in Error!" in a Full Report or"One or more Bars are in Error!" in a Screening mode. P...

2 - 1 2 Quick*View Quick*View Demonstration Software Instructions Quick*View is a Microsoft Windows ® program that displays decoded symbol messages and captures images (for instance, ID photographs) from the imager. Bar code information and images are displayed in the Quick*View window. Note: For ad...

2 - 2 8. Double click on the Quickview.exe file. Follow the screen prompts to install the Quick*View program. 9. To start Quick*View, from the Start Menu click on Programs , Quick*View , Quick*View . Note: If you wish, you can create a shortcut to the Quick*View executable on your desktop. Temporary...

2 - 3 Using the Quick*View Software Upon startup, the Quick*View splash screen appears for approximately three seconds. Quick*View will then attempt to establish communications with the Imager. If Communication Cannot Be Established This message appears if communication cannot be established: Quick*...

2 - 4 Scan Data Window Once successful communication has been established, you can scan codes and display the bar code data in a window. Select View - Scan Data Window . As you scan bar codes, the data appears in the Serial Scan Data Window. You can alter the font in this window by using the Font bu...

3 - 1 3 Customer Support Obtaining Factory Service HHP provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, return the unit to HHP (postage paid) with a copy of the dated purchase record attached. Contact the appropriate loca...

3 - 2 Technical Assistance If you need assistance installing or troubleshooting your imager, please call your Distributor or the nearest HHP technical support office: North America/Canada: Telephone: (315) 685-2476, Option 4 (8 a.m. to 6 p.m. EST) or in the U.S. (800) 782-4263 Fax number: (315) 685-...