Page 2 - NEED MORE INSTRUCTIONS?; WARNING; CAUTION
w The manufacturer has made every effort to eliminate any sharp edges. However, you should handle all components with care to avoid accidental injury. WARNING NOTICE: Before assembly, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the appliance. Contac...
Page 3 - Screws and install leg cap.
3 w IMPORTANT: Please read all instructions thoroughly before proceeding. Find a large, clean area in which to assemble your HALO Prime550 Pellet Grill. Please refer to the assembly diagram, as necessary. Install Left-Inner Leg using (3)-M6 x 14mm Screws and install leg cap. 1 Leg Cap Left-Inner Leg...
Page 5 - Install Left Outer Leg Assembly, Left Inner Leg
5 Install Left Outer Leg Assembly, Left Inner Leg assembly using pivot bracket 68 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1)-M6 x 63mm Knob w/ Threaded Shaft and Nylon-Spacer. Tighten screws firmly. Set assembly aside. 3 Pivot Bracket-BPivot Bracket-CM6 x 63mm-Knob w/ Threaded Shaft Nylon S...
Page 8 - Install Right Outer Leg Assembly, Right Inner Leg
8 Install Right Outer Leg Assembly, Right Inner Leg assembly using pivot bracket 69 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1) x 63mm -Knob w/ Threaded Shaft and Nylon- Spacer. Tighten screws firmly. Set assembly aside. 6 Pivot Bracket-BPivot Bracket-CM6 x 63 mm Knob w/ Threaded Shaft Nylon...
Page 9 - Install Front Panel and Rear Brace assembly
9 Install Front Panel and Rear Brace assembly using (8)-M6 x 14mm screws. 7 Rear Bracket Front Panel RISE ABOVE Logo Plate M6 x 14mm Screw ITEM PART DESCRIPTION 70 71 72 QTY. 111 8 IMPORTANT: Do not tighten screws completely until all screws for that step have been installed. 71 82 82 82 70 82 72 82
Page 10 - Attach the Casters using M12 caster wrench.
10 Caster with Lock Caster-Swivel ITEM PART DESCRIPTION 74 73 QTY. 22 Attach the Casters using M12 caster wrench. Mount Casters with Lock to front legs and Mount Swivel casters to rear legs. 8 NOTE: You can lock the casters that have locks, allowing you to assemble the caster without using a caster ...
Page 11 - Attach Brackets-Leg Support-Left and right
11 Attach Brackets-Leg Support-Left and right using 6-M6 x 12 Truss head screws. 9 Bracket-Leg Support-LeftBracket-Leg Support-RightM6 x 12 mm Screw ITEM PART DESCRIPTION 61 62 80 QTY. 11 6 61 62 80 80
Page 13 - Install cooking grid and warming rack.
13 Install cooking grid and warming rack. 11 Warming RackCooking Grid ITEM PART DESCRIPTION 5 QTY. 11 8
Page 14 - Warming rack continued.
Warming rack continued. 11 Warming rack is in usual position. Step1. Slide warming forward until center support wire is pushed against front section of the bracket. Step2. Left up warming then hook on to the “J” brackets. 14
Page 15 - Install side table brackets left and right using
15 12 Install side table brackets left and right using (12)-M6 x 14mm screws. Install side table left and right using (4)-M6 x 2.5H x 9.5D-Shoulder Screw. ITEM PART DESCRIPTION 19 20 22 23 QTY. 24 25 81 Bracket-Side Table-ABracket-Side Table-BRelease Spring Pin-Side Table/Cleanout TraySide Table-Rig...
Page 17 - Install grease cup with cover.
Install grease cup with cover. Grease Bucket w/ Cover ITEM PART DESCRIPTION 26 QTY. 1 26 17 14
