Haier HWM90-0713S- Manuals

Page 2 - Contents

Contents Names of the parts - - - - - - - - - - - - - - - - - 1Safety precautions - - - - - - - - - - - - - - - - - 2Installation and adjustment - - - - - - - - - - - 4Preparation before washing - - - - - - - - - - 6The musts in washing - - - - - - - - - - - - - - - 7Usage of the detergent - - - - -...

Page 3 - Meaning and description of the symbols; Warning sign; Names of the parts

1 Meaning and description of the symbols Warning sign Forbidding sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents, otherwise it may cause damage of the machine or injure the person...

Page 4 - Safety precautions

Safety precautions Please insert the power cord into special receptacle with rated vol-tage. Be sure to use single-phase three pins receptacle. The earthing terminal of the receptacle must be earthed reliably. If possible, please adopt electric leakage protector. When the machine is normallyusing, p...

Page 6 - Installation and adjustment; Install the lint filter; The drainage shall be smooth with the drain hose.

Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package, please take out the lint filter from the document bag, install it ...

Page 7 - H o w t o c h a n g e t h e d i r e c t i o n o f t h e d r a i n h o s e s; Install the water inlet hose Select the water level; Extend the drain hose from the side of spin tub

5 H o w t o c h a n g e t h e d i r e c t i o n o f t h e d r a i n h o s e s Install the water inlet hose; Select the water level Insert the water inlet hose into the water-fillingentrance on the control pane directly.(pull itout to dismantle it) Select water level according to thequantity of the l...

Page 8 - Preparation before washing; Pay attention to followings before washing the laundries

Preparation before washing 6 Preparation before washing1.Connect the water inlet hose.2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe.3.Put down the drain hose . 4.Slanting o...

Page 9 - The musts in washing; How to use the whitener; How to use the washing powder; Usage of the detergent

The musts in washing 7 The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. The thickness ,size , type o...

Page 10 - Washing sequence; Wash

Washing sequence 8 Figure 3 Spin timer Wash timer (To set to below 2 minute, first set to 6 minute then turn it back. it can increase the service life of the timer). (to set to below 1 minute, first set to 2 minute then turn it back. it can increase the service life of the timer). Wash Figure 2 Figu...

Page 11 - Rinsing

9 Rinse with stored water Rinse with water-filling 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is a few , please use "Stan...

Page 12 - Spinning

To do spinning and draining together, please first do spinning for around 1 minute, then do draining . Otherwise the spinning will stop owing to too much water stored in the spin tub. In spinning, it will pause the work if you open the outer cover of the spin tub. Close it to resume the spinning. 10...

Page 13 - Take off the overflow filter.; Cleaning the overflow filter; Cleaning the lint filter; Disposal after washing

11 After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine.Please first pull off the power plug from the receptacle before cleaning. 1 Take off the overflow filter. As indicated in the figure, nip the ...

Page 14 - Clean the safeguard cover

12 Cleaning the overflow filter 2. Take off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1).3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water.4. Install the overflow filter. (1).Inst...

Page 15 - Disposal of the complete unit; If the laundries fall to the outer side of the spin tub,; contact the after-sales service department.; If the laundries fall to the outer side of the spin tub; When the remained water is frozen; Trouble-shooting Answer to question

13 Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty. Do not wash it directly by water. After washing, dismount the water inlet hose.Do not store water in the tub for long period. Discharge the water immediatelyafter each using.Pull off the power plug and h...

Page 16 - Phenomena The reason

14 Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or aft...

Page 17 - Packing list; Twin-tub washing machine

15 Water inlet hose Gland Lint filter Packing list Twin-tub washing machine Name Quantity User's manual One piece One piece One piece One piece One set

Page 18 - Specification; Injection pressure(MPa

16 Specification Water level/Water quantity (L) (about) Maximum/48 Medium/39 Minimum/33 Injection pressure(MPa ) 0.02 0.2 Washing capacity(kg) 6.0 Spinning capacity(kg) 4.5