Haier HWM70-918NZP - Manuals

Page 2 - Safety precautions; Forbidden sign; Meaning and description of the symbols

2 Safety precautions Contents marked with that symbol are actions forbidden to perform. Performing of those actions may result in damage of the machine or injure the personal safety of the user. Forbidden sign Contents marked with that symbol are related to the safety of the product and the personal...

Page 5 - Installation and adjustment

5 Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. 1. Move the control handle of trundle to the point 1 and the control handle fix on the second reference column; The...

Page 6 - Confirm the water faucet

6 Screw knife Figure 4 Figure 5 About 4mm before twisting About less than 2mm after twisting Screw Bushing Sign plate Screw nut Figure 2 Figure 3 Figure 6 2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet...

Page 8 - The drain hose shall drain smoothly.; How to change the direction of the drain hose

8 The drain hose shall drain smoothly. Do not trample or press the drain hose. 2 The height of the drain hose shall be less than 10cm , or the drainage will not be smooth, and cost such long time that the machine may stop at mid way. 1 3 5 4 If the drain hose is too long, cut it at mid point. To mak...

Page 9 - Preparation before washing; Pay attention to followings before washing the laundries

9 Preparation before washing Connect the water inlet hose. Open the water faucet.  Con ﬁ rm that the washing machine is earthed reliably. Then insert the power plug into the receptacle. The earth terminal shall not link to gas pipeline and faucet water pipeline.  Put down the drain hose.  Slantin...

Page 11 - Use the operation buttons

11 Use the operation buttons Off On: indicate the program about to run,or indicate the selected mode or indicate the water level Flashing: indicate the running program During sensing, it displays “--” .During delay procedure, it displays the remained delay time (in hours). During operation of progra...

Page 12 - Push “ ” “ ” “ ” button to select suitable; Push the “ ” button, select suitable water level; procedure program; Push the “ ” button, select suitable reserve water times

12 Push the “ ” button to switch on the power Push the “ ” button to select suitable automatic program It has the special power resume function. In the case of power failure or the power plug is loose during running, the machine can save the running program, and resume the program after the power su...

Page 13 - Disposal after washing; Clean the detergent box and set it on the control panel seat:

13 Push the “ ” button to select suitable delay wash program After switching on the power, the delay time program is set to off mode automatically. If you need to set the washing procedure to be ﬁ nished at delay time, please push the “DELAY” button to set the delay wash program. Refer to delay butt...

Page 14 - Cleaning the lint

14 1 2 3 4 Cleaning the lint ﬁ lter: Push down the spring piece at the top of the lint ﬁ lter to make the claws out of the ﬁ lter cover, and then pull out the lint ﬁ lter to get it down.(figure 1) Put the lint ﬁ lter into ﬁ lter cover, and make it tight . Make sure the lint ﬁ lter well installed, or...

Page 15 - Trouble-shooting Answer to question; Phenomena

15 Trouble-shooting Answer to question Phenomena The reason How to settle The digitron displays E0. The top lid is open during reserve procedure. Close the top lid.  The drainage cannot work, or is too slow. The digitron displays E1. Is the drain hose put down? Is the drain hose blocked? Put down t...