Haier HW70-B1486-F - Manuals

05 BEFORE USE SAFETY INSTRUCTIONS DO ... ... Make sure that the transport bolt are removed. ... Use a separate earthed socket for the power supply. ... Make sure that the plug is accessible. ... Hold the plug and not the electric cable when unplugging the power supply. ... Make sure that the fuses i...

06 BEFORE USE DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. Remove the back cover. 1. Remove the four bolts on the rear side and take out the synthetic 2.stabilisers fro...

07 BEFORE USE 1. 2. 1. 8 0 -1 0 0cm 2. INLET HOSE 1. Connect the nut on the inlet hose to the connector on the water valve. 2. Apply inlet hose to a water tap with cold, fresh water. Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused. DRAIN HOSE 1. Use the drain h...

08 BEFORE USE OPERATIONAL FUNCTIONS AA CONTROL PANEL A Power Switch B Program knob C M emo button D Spinning Speed Setting button E Washing temperature button F Display screen G Washing time H Times of rinse I Spinning time J Detergent distribution drawer A ¬ Power Switch _ Press this button to swit...

09 BEFORE USE F Displayscreen _Display washing time, remaining time, times of rinsing, spinning time, temperature setting value, speed setting value, child lock state, door lock state, washing progress and alarm message, etc. G Washing time Press the “Wash” button to set washing time. Press and hold...

2 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Compartment for softener and other additives 2 1 1 3 2 10 APPLIANCE USING THE PROGRAM SELECTION PROGRAM MODES Preset spin speed Program Maximum Preset 2 3 1 RecommendedLaundry 1 ¬ Hand Wash - - to 40 °C 30°C Cotton fabrics 800 rpm ...

11 USING THE APPLIANCE CONSUMPTION AND TECHNICAL DATA TECHNICAL DATA CONSUMPTION TABLE PROGRAM MAX. LOAD HW70-*86-F/HW80-*86-F HW*-1286-F/HW*-1486-F TEMPERATURE WASHING TIME ¬ Hand Wash 2kg/2 kg 30°C 0:38 ¬ Wool 2kg/2 kg 30°C 0:35 ¬ Delicate 2kg/2 kg 30°C 0:38 ¬ Mix o t u A g k 5 / g k 5 ¬ Synthetic...

12 APPLIANCE USING THE WASHING METHODS POWER SUPPLY Connect the washing machine to the power supply (220V to 240V~/50Hz). WATER CONNECTION Turn on the tap. The water must be clean and clear. Note: Before use, check for leakage in the joints between the tap and the inlet hose by turning on the tap. P...

13 USING THE APPLIANCE LOADING THE MACHINE Open the washer door, put in the laundry piece by piece. Close the door tightly.¬ When first using the washing machine, let it run unloaded for one program to prevent the laundryfrom being tainted by oil or dirty water from the washing machine. Before washin...

14 APPLIANCE USING THE SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected . SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected.See "Opera-tional functions" on the "Control panel" pa...

15 USING THE APPLIANCE Bed sheet (single) Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric clothes / Approximately 800g Jackets Cotton Approximately 800g Jeans / Approximately 800g Overalls Cotton Approximately 950g Ladies Pyjamas / Approximately 200g Shirts / Approximately ...

16 1. 2. 1. 2. MAINTENANCE CLEANING & CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash. Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace th...

17 MAINTENANCE WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of foreign substances, clean the water inlet valve and inlet valve filter regularly. MOVING THE MACHINE If the machine is to be moved to a distant location, replace the transportation bolts remo...

18 MAINTENANCE DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS ¬ Control panel lock function: Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program. It can no longer be changed by operating buttons or knobs. To unlock press the "D...

19 MAINTENANCE TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confi rmed. PROBLEM CAUSES SOLUTIONS Washing machine fails to operate. ¬ Poor connection to the power supply.¬ Power failure.¬ The washer...