Haier HW55-1010 - Manuals

05 BEFORE USE SAFETY INSTRUCTIONS DO ... ... Make sure that the transport bolt are removed. ... Use a separate earthed socket for the power supply. ... Make sure that the plug is accessible. ... Hold the plug and not the electric cable when unplugging the power supply. ... Make sure that the fuses i...

06 BEFORE USE DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. Remove the back cover. 1. Remove the three bolts on the rear side and take out the synthetic 2. stabilisers f...

07 BEFORE USE INLET HOSE 1. Connect the nut on the inlet hose to the connector on the water valve. 2. Apply inlet hose to a water tap with cold, fresh water. Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused. DRAIN HOSE 1. Use the drain hose bracket to keep the e...

Pre-Wash Wool Power Cotton Remaining Time Quick C 。 90 C 。 60 C 。 40 C 。 40 C 。 30 60’ 30’ 15’ 1000 800 600 400 Synthetic Spin Cold Speed Stop Strong Start/Pause 5.5kg HW55-1010 08 APPLIANCE USING THE OPERATIONAL FUNCTIONS CONTROL PANEL A Detergent distribution drawer B Power Button C Program knob D...

10 APPLIANCE USING THE PROGRAM SELECTION PROGRAM MODES Pr Program ogramm Temperature 2 3 3 1 Recommended Laundry ne 1 Cotton ¬ Prewash 60°C Very heavy soiling 1000 rpm 2 ¬ 90°C 90°C Heavy soiling 1000 rpm 3 ¬ 60°C 60°C Soiled cotton 1000 rpm 4 ¬ 40°C 40°C Non-fade and medium soiled 1000 rpm 5 ¬ Quic...

11 USING THE APPLIANCE CONSUMPTION AND TECHNICAL DATA TECHNICAL DATA CONSUMPTION TABLE The wash cycle times are intended as a guide only. The actual time used may vary due to different water pressure, initial water temperature, etc. * ) EN 60456 test program / Energy label program with Cotton 60°C ,...

12 APPLIANCE USING THE WASHING METHODS POWER SUPPLY Connect the washing machine to the power supply (220V to 240V~/50Hz). WATER CONNECTION Turn on the tap. The water must be clean and clear. Note: Before use, check for leakage in the joints between the tap and the inlet hose by turning on the tap. P...

13 USING THE APPLIANCE LOADING THE MACHINE Open the washer door, put in the laundry piece by piece. Close the door tightly. ¬ When fi rst using the washing machine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine. Before wa...

14 APPLIANCE USING THE TIPS FOR SAVING ENERGY Collect clothes for one full wash load. 1. Avoid overloading the washing machine. 2. Prewash only heavily soiled clothes. 3. Reduce the amount of detergent or choose standard or delicate wash programs for slightly soiled clothes. 4. Choose a proper washi...

15 USING THE APPLIANCE Bed sheet (single) Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric clothes / Approximately 800g Jackets Cotton Approximately 800g Jeans / Approximately 800g Overalls Cotton Approximately 950g Ladies Pyjamas / Approximately 200g Shirts / Approximately ...

16 MAINTENANCE CLEANING & CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash. Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace the drain hose...

MAINTENANCE WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of foreign substances, clean the water inlet valve and inlet valve fi lter regularly. MOVING THE MACHINE If the machine is to be moved to a distant location, replace the transportation bolts remove...

18 MAINTENANCE DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS ¬ Foam test function: If the washing machine fi nd much foam,the LED lamp of “time to end” will twinkle completely for 15 mins,then the washing machine will go on washing. of course, you can touch “Start/pause” to cancel this function.B...

MAINTENANCE TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confi rmed. PROBLEM CAUSES SOLUTIONS Washing machine fails to operate. ¬ Poor connection to the power supply.¬ Power failure.¬ The washer do...