Haier HSU-09RF03/R2- Manuals

FAN DRY HEAT COOL AUTO Operation 1. Mode display 2. SWING display 3. FAN SPEED display 4. SLEEP display 5. LOCK display6. SIGNAL SENDING7. TIMER OFF display 8. TIMER ON display 9. CLOCK display 10. TEMP display 11. POWER ON/OFF Used for unit start and stop. 12. MODE Used to select AUTO run, COOL, DR...

Operation Buttons and display of the remote controller. like the following figure: If the unit which you purchased has healthy function, Remote controller should BRIEF INTRODUCTION TO HEALTH OPERATION The anion generator in the air conditioner can generate a lot of anion to effectively balance the q...

Remote controller's operation When in use, put the signal transmission head directly to thereceiver hole on the indoor unit.The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.Don't throw the controller, prevent it from being damag...

(4) Unit stop (1) Unit start Auto run, Fan operation Enjoy yourself by just a gentle press. mode changes as follows: Press ON/OFF button, unit starts.Previous operation status appears on display.(Not Timer setting)Power indicator on indoor unit lights up. (2) Select operation mode Press MODE button....

Press MODE button. For each press, operation Recommendations: COOL,HEAT and DRY operation Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (1) Unit start mode changes as follows: Press ON/OFF button, unit starts. Previous operation status appears on display. (Not...

(5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode.Referring to the Fig. COOL HEAT COOL HEAT About 10 o About 10 o better set a temp. difference of 3-5 o C between indoor and outdoor temp. in COOL mode. Hints As cold air fl...

TIMER Operation You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. Set Clock correctly before starting Timer operation TIMER ON/OFF Power indicator on indoor unit lights up. (1)After unit sta...

TIMER ON-OFF To cancel TIMER mode Power indicator on indoor unit lights up. (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. ON OFF ON OFF TIMER ON TIMER OFF TIMER ON-OFF blank Every time the button is pressed, display changes as follows: (2) Press TIM...

HEALTH Mode operation (1) Press the ON/OFF switch. (2) Press the "HEALTH" once," " is displayed, now the air conditioner is operating the health function. (3) Press the "HEALTH"again,then the health function stops. The anion generator in the air conditioner can generate a lot...

Emergency Operation: Pi Pi Emergency operation and test operation Carry out this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, a" Pi "sound starts once, which means the start of this operation. In this operation, it is not pos...

Comfortable SLEEP In COOL mode sleep in selected mode. Before going to bed at night, you can simply pressthe SLEEP button and unit will bring you a sound One hour after SLEEP mode starts, temp. willbecome 1 o C higher than temp. setting. After running for another 1 hour, temp. rises by 1 o C further...

Different models have different appearance Cleaning of unit casing Cleaning of remote controller Cleaning of air filter Cut off power supplybefore cleaning unit casing with soft cloth.In case of heavy stain, clean it with neutral detergent.squeeze water in the cloth, wipe off the detergent on unitca...

Better use of air conditioner Proper room temperature. Cleaning of the air filter. Effective use of the timer. Closing of doors and windowsduring operation Never fail to observe the followings Do not sprinkle water over the unit. Do not block the inlet or outlet. Do not pull power plug. Do not use f...

Before asking for service, check the following first. NormalPerformanceinspection Noise is heard Phenomenon Cause or check points The system does not restart immediately. Smells are generated. Mist or steam are blown out. Multiple check Does not work at all. Poor cooling Application temp. range of a...