Haier HBS82-880- Manuals

Page 2 - Names of Parts; Caution and Warning symbols

Names of Parts Detergent distributor Top program knob Operation button Door Porthole Drainage hose clip Back plate Earth terminal Power supply cable Back plate screw (3) Packing bolt (3) Temperature knob Caution and Warning symbols For your safety and to prevent damages to the washing machine, any i...

Page 3 - Matters Needing Attention

1 Matters Needing Attention 1. A separate earthed socket is required for thepower supply. After installation of the washingmachine,the power plug should be accessibleduring the normal wash. 3. Fuses in the power circuit should be ratedfor 15A. Refer to a washing machine techni-cian or a Haier design...

Page 6 - Installation

Installation 4 Fig 1 As shown in figure1 remove all the packing materials (including the foam base). Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock duringtranspor tation The steps below should be followed beforeusing the appliance,1. Remove the rea...

Page 8 - Control Panel

6 Control Panel A Washing program Turn the knob clockwise to set the desired wash program .Caution: Turn off the power and turn the program knob clockwisefor setting desired wash program. B Washing temperature Turn the knob clockwise to set the desired temperature.Temperatures between 30 O C-90 O C ...

Page 9 - Operational Functions

7 Operational Functions G Power light The light will illuminates when the power supply is connected. F Power button Press the button ,washing machine will working;release the button,the washing machine will stop. ON OFF ON OFF 7 E Economic wash button Pressing this button will reduce the consumption...

Page 10 - Program Selection

8 Program Selection NOTE: “o”means softener liquid detergent canbe added when necessary. “ ”means detergent can be added when necessary. “ ”means no detergent can be added. 8 15 20 20 45 22.5 5 12.5 5 10 5 25 10 7.5 7.5 25 10 7.5 7.5 x

Page 11 - Preparation

9 1. Power supply Plug in the power supply 220V~/50Hz. 3. Laundry treament 2. Water supply Turn on the tap ensure that the water is clear.Caution: Before staring the washing machine turn on thewater faucrt to ensure that the water faucet and the waterinlet hose are connected correctly and do not lea...

Page 12 - Washing Methods

Washing Methods 10 1. Laundry loading Evenly load the laundry in the washingmachine and then tightly close the doorof the washing machineNote: 1) When first using the washing ma-chine, let it run unloaded for one programto prevent the laundry from being taintedby oil or dirty water from the washing ...

Page 14 - Maintenance

12 Maintenance 6. If the machine is to be moved a distance location,replace the vibration mounting locks which were re-moved during installation as shown below. 1. Turn of the water and electricity supplyafter every wash. Open the door to pre-vent the formation of moisture and odors.If the washing m...

Page 15 - Trouble shooting

13 Trouble shooting The following circumstances do not constitute problems. Do not contact the main-tenance service until the problem has been confirmed. Problem Possible Cause Poor connection to power supply Power failure Door is not properly closed Machine has not been switched on Washing machine ...

Page 16 - Technical Specification

14 Technical Specification Model Item Power supply HBS82-880 220V~/50Hz Maximum working current (A) Water pressure (MPa) Washing power (W) Spinning power (W) 0.05 P 1 330 650 10 Heating power (W) Size (HXDXW) (mm) Weight (kg) 15 1950 72 8 5 0 x 5 5 0 x 5 9 5 Washing program 14 HBS82-880

Page 17 - Wiring Circuit

I1: Power Switch EVC,EVP,EVL: Water valve I2: Economic wash Switch P1,P2: Pressure Switch I3: No spin Switch THR: Adjustable Thermastat MR: Door Lock D: Drain Pump TM: Timer motor MC,ML: Motor H:Heating Element C: Capacitance Wiring Circuit 15 15 I3: No spin Switch I 2 : E c o n o m i c w a s h Swit...